manualshive.com logo in svg

Graco SG2, Инструкция по эксплуатации и обслуживанию, Страница: 4 / 37

Поделиться
Скачать
Graco SG2 Скачать руководство пользователя страница 4

1-1

Spindl-Gard SG-1 and SG-2 Systems

L42110

1.1 

PURPOSE OF MANUAL

1.1.1 

 

This manual is designed for users of Spindl-Gard 

systems designated SG-1 (for multi-spindle heads) 

and SG-2 (for precision spindles). Procedures and 

instructions are pro vided for installation, start-up, 

operation, troubleshooting and maintenance. Although 

the components and assemblies used will vary 

between different systems there are common rules and 

procedures which apply to any installation.

1.1.2  

The SG-1 and SG-2 systems use many similar com-

ponents and some procedures discussed in the manual 

apply to both types of systems. If procedures differ 

between the systems, the procedures are covered 

separately to allow the user to quickly locate the specific 

area of concern. A table of contents is provided at 

the start of each section to allow for quick and easy 

reference.

1.1.3 

Refer to Bulletin L20110 for additional SG-1 and  

SG-2 system and product specifications.

1.2 

SPINDL-GARD OVERVIEW

 

Spindl-Gard was developed to lubricate single and multi-

spindle machining heads. A unique spray nozzle utilized 

with other Spindl-Gard components provides precise 

amounts of oil to a specific bearing surface. Oil is applied 

at the proper frequency and in the right quantity to meet 

the lubrication requirements, keeping bearings, gears, 

shafts and seals run ning cool. Spindl-Gard provides full 

protection without over-or under-lubing.

1.3 

SG-1 COMPONENTS AND OPERATION 
OVERVIEW

1.3.1 

General. 

SG-1 utilizes a standard Trabon pump package 

(typically, Graco’s Modu-Flo

®

 series), a Model MSP 

lubricant divider valve with cycle indicator switch, Maxi-

Monitor

®

 controller, and various fluid line accessories. 

(See Figure 1-1.) In some cases, the machine controller 

will be used in lieu of the Maxi-Monitor controller. Each 

shot of lubricant from the pump is distributed by the 

divider valve to the appropriate lube point. Depending 

upon machining head design, some bearings may 

receive lubricant directly from the divider valve while 

others, including gears, may receive lubricant from spray 

nozzles located in the gear cavity. Pressure switches 

may be used to monitor air pressure in the machining 

head. By using the feedback features of the divider 

valve, it is possible to monitor lubricant and pressure 

delivery status to all points at all times. An SG-1 circuit is 

shown in Figure 1-1.

1.3.2 

SG-1 Components

1.3.2.1  General.

 Paragraphs 1.3.2.2 through 1.3.2.9 pro vide 

a brief description of components used in typical SG-1 

systems. See Section 5, parts ordering information, for 

corre sponding part numbers.

SECTION 1

INTRODUCTION 

1.1.PURPOSE OF MANUAL ...................................................... 1-1

1.2.  SPINDL-GARD OVERVIEW .............................................. 1-1

1.3.SG-1 COMPONENTS AND OPERATION OVERVIEW .............. 1-1

    1.3.1 General ................................................................. 1-1

    1.3.2 SG-1 Components ................................................. 1-1

    1.3.3 SG-1 Operation ..................................................... 1-3

1.4.SG-2 COMPONENTS AND OPERATION OVERVIEW .............. 1-4

    1.4.1 General ................................................................. 1-4

    1.4.2 SG-2 Components ................................................. 1-4

    1.4.3 SG-2 Operation ..................................................... 1-4

OPERATION AND 

SERVICE INSTRUCTIONS

Содержание SG2






































Отзывы:

Нет отзывов