Graco SDL23 Series Скачать руководство пользователя страница 2

Страница: 2 / 54

Contents

3A8626C

Contents

Related Manuals. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

SDX Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

XDX Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Typical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Overhead-Mounted Hose Reel . . . . . . . . . . . . . . 7

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Required Components. . . . . . . . . . . . . . . . . . . . . 8

Pressure Relief Procedure . . . . . . . . . . . . . . . . . . 9

Flush the Equipment . . . . . . . . . . . . . . . . . . . . . . 9

Installation Mounting Options . . . . . . . . . . . . . . 11

Reel Bank Mounting Location’s

Selection . . . . . . . . . . . . . . . . . . . . . . . . 11

All Mountings. . . . . . . . . . . . . . . . . . . . . . . . 11

All Models . . . . . . . . . . . . . . . . . . . . . . . . . . 12

SDX or XDX Models Only . . . . . . . . . . . . . . 12

Ceiling Installations . . . . . . . . . . . . . . . . . . . . . . 14

Ceiling Mount Without an I-Beam - Open

Channel (All Models) . . . . . . . . . . . . . . . 15

Ceiling Mount Directly to an I-Beam without

Drilling holes - All Models . . . . . . . . . . . 16

MOUNTING BRACKET KIT: 204741 . . . . . . 16

Wall Installations . . . . . . . . . . . . . . . . . . . . . . . . 17

Hose Installation . . . . . . . . . . . . . . . . . . . . . . . . 18

Installation of Hose on a Bare Reel . . . . . . . 18

Adjust Spring Tension . . . . . . . . . . . . . . . . . . . . 20

Single Pedestal SDX Model Hose Reels . . . 20

Dual Pedestal XDX or XNX Model

Hose Reels . . . . . . . . . . . . . . . . . . . . . . 20

Recycling and Disposal . . . . . . . . . . . . . . . . . . . . . 22

End of Product Life . . . . . . . . . . . . . . . . . . . . . . 22

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Replace Spool - Single Pedestal SDX Models. . 24

Replace Spool - Dual Pedestal XDX or

XNX Models . . . . . . . . . . . . . . . . . . . . . . . . . 25

Replace the Hose. . . . . . . . . . . . . . . . . . . . . . . . 27

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

SDX Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Parts SDX Series . . . . . . . . . . . . . . . . . . . . . . . . 31

XDX Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Parts XDX Series . . . . . . . . . . . . . . . . . . . . . . . . 34

XNX Models . . . . . . . . . . . . . . . . . . . . . . . . . 36

Parts XNX Series . . . . . . . . . . . . . . . . . . . . . . . . 37

Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

H ose Reel Label. . . . . . . . . . . . . . . . . . . . . . 39

Label, Fluid Identification: 24A223 . . . . . . . 40

Latch Kit: 15Y503. . . . . . . . . . . . . . . . . . . . . . . . 40

Enclosure Retrofit Kit: 24C100 . . . . . . . . . . . . . . 40

Hose Inlet Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Mounting Adapter: 22A224 . . . . . . . . . . . . . . . . 41

Hose Guide Kits . . . . . . . . . . . . . . . . . . . . . . . . . 41

Roller Bracket Repair: 218591. . . . . . . . . . . 41

Cabinet Mounting Kit: 15Y478. . . . . . . . . . . 41

Hose Reel Stop Kit. . . . . . . . . . . . . . . . . . . . . . . 41

1/4 in. and 3/8 in. ID Hoses: 218340 . . . . . . 41

3/8 in. and 1/2 in. ID Hoses: 218341 . . . . . . 41

1/4 in. ID Hoses: 222225 . . . . . . . . . . . . . . . 41

D imensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

SDX Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

XDX Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

XNX Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Mounting Channel Dimensions . . . . . . . . . . . . . 45

Si de Dimension (All Models). . . . . . . . . . . . . . . . 50

Technical Specifications . . . . . . . . . . . . . . . . . . . . 51

California Proposition 65 . . . . . . . . . . . . . . . . . . . . 52

Graco 7-Year Hose Reel Warranty. . . . . . . . . . . . . 53

Содержание SDL23 Series























































Результаты поиска

Содержание SDL23 Series

Отзывы:

Похожие инструкции для SDL23 Series

Бренды по названию

Популярные бренды

Graco SDL23 Series, Инструкция по эксплуатации

Результаты поиска

Содержание SDL23 Series

Отзывы:

Похожие инструкции для SDL23 Series

Бренды по названию

Популярные бренды