Graco SDL23 Series Скачать руководство пользователя

Страница: 27 / 54

Repair

3A8626C

21. Tighten the bolt (18) (torque 25 - 35 ft-lb/33.9 - 47.5

N•m).

22. Align the guide arm (29) and guide arm (30), then

install screws (27) and tighten (torque 20 - 30

ft-lb/27.1 - 40.7 N•m).

23. Align the pedestal assembly (26) to the base (24).

Install two screws (27) and tighten (torque 20 - 30

ft-lb/27.1 - 40.7 N•m).

24. Re-install the reel to the ceiling or wall.

25. Install the hose onto the spool following the

Hose

Installation

instructions, page 18.

26. Flush the hose following

Flush the Equipment

page 9.

27. Set the spring tension following

Adjust Spring

Tension

, page 20.

Replace the Hose

1. Follow the

Pressure Relief Procedure

, page 9.

2. Fully extend the hose (B) and latch the reel (F

. 24).

3. Attach a C-clamp (A) to the reel flange to prevent

the reel from unintentionally becoming unlatched

and spinning freely (F

. 24).

4. Remove the hose stop from the hose end and put

all of the parts in a secure place for re-installation

on the new hose (F

. 25).

a. Loosen and remove screws and nuts (F

. 25).

b. Separate the two hose stop components to

remove from the end of the hose (F

. 25).

SPRING TENSION HAZARD

The hose reel spring is always under great tension,

which if released in an uncontrolled manner could

cause serious injury.
• Never allow the reel to spin freely. Uncontrolled

spinning could cause serious injury if hit by the

hose.

• Securely fasten the reel in place while making

adjustments.

• The hose reel spring is not a serviceable part, Do

not attempt to replace or service the hose reel

spring.

• Always wear heavy gloves while adjusting the

spring tension to protect your hands from being

cut on the hose reel.

. 24

Содержание SDL23 Series























































Результаты поиска

Содержание SDL23 Series

Отзывы:

Похожие инструкции для SDL23 Series

Бренды по названию

Популярные бренды

Graco SDL23 Series, Инструкция по эксплуатации

Результаты поиска

Содержание SDL23 Series

Отзывы:

Похожие инструкции для SDL23 Series

Бренды по названию

Популярные бренды