Graco Reactor 2 E-30i Скачать руководство пользователя страница 80

Страница: 80 / 94

USB Data

Create Custom Language Strings

The custom language ﬁle is a tab-delimited text ﬁle

that contains two columns. The ﬁrst column consists

of a list of strings in the language selected at the

time of download. The second column can be used

to enter the custom language strings. If a custom

language was previously installed, this column

contains the custom strings. Otherwise the second

column is blank.
Modify the second column of the custom language ﬁle

as needed and the follow

Upload Procedure, page 80

to install the ﬁle.
The format of the custom language ﬁle is critical.

The following rules must be followed in order for the

installation process to succeed.
• Deﬁne a custom string for each row in the second

column.

Note

If the custom language ﬁle is used, you

must deﬁne a custom string for each

entry in the DISPTEXT.TXT ﬁle. Blank

second-column ﬁelds will be displayed

blank on the ADM.

• The ﬁle name must be DISPTEXT.TXT.
• The ﬁle format must be a tab-delimited text ﬁle

using Unicode (UTF-16) character representation.

• The ﬁle must contain only two columns, with

columns separated by a single tab character.

• Do not add or remove rows to the ﬁle.
• Do not change the order of the rows.

Upload Procedure

Use this procedure to install a system conﬁguration

ﬁle and/or a custom language ﬁle.

1. If necessary, follow the Download Procedure to

automatically generate the proper folder structure

on the USB ﬂash drive.

2. Insert USB ﬂash drive into USB port of computer.
3. The USB ﬂash drive window automatically opens.

If it does not, open USB ﬂash drive from within

Windows Explorer.

4. Open GRACO folder.
5. Open the system folder. If working with more

than one system, there will be more than one

folder within the GRACO folder. Each folder is

labeled with the corresponding serial number of

the ADM. (The serial number is on the back of

the module.)

6. If installing the system conﬁguration settings

ﬁle, place SETTINGS.TXT ﬁle into the UPLOAD

folder.

7. If installing the custom language ﬁle, place

DISPTEXT.TXT ﬁle into the UPLOAD folder.

8. Remove USB ﬂash drive from the computer.
9. Install USB ﬂash drive into the ADM USB port.
10. The menu bar and USB indicator lights indicate

that the USB is downloading ﬁles. Wait for USB

activity to complete.

11. Remove USB ﬂash drive from USB port.

Note

If the custom language ﬁle was installed,

users can now select the new language

from the Language drop-down menu in

Advanced Screen 1 — General, page 50

332636C

Содержание Reactor 2 E-30i































































































Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды

Graco Reactor 2 E-30i, Операция

Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды