Graco Reactor 2 E-30i Скачать руководство пользователя страница 39

Страница: 39 / 94

Setup

Install Wall (optional)

It is only possible to install a wall between the

proportioner and generator for systems without an air

compressor.

Beneﬁts:
• Temperature condition the trailer space where

chemical is stored. Check with chemical

manufacturer for chemical storage temperatures.

• Reduce noise for the operator while the Reactor

is running.

The supplied fuel lines and battery cable may need

to be replaced if a wall is installed between the

proportioner and generator. Purchase the Fuel Line

and Battery Cable Extension Kit 24K333.
1. If necessary drain coolant from system. See

Reactor repair manual for complete instructions.

Coolant lines do not need to be disconnected to

install a wall.

Note

Battery must be connected to starter to

drain coolant from system.

2. Remove screws and battery bracket from the

pallet.

Remove Battery Bracket and Fuel Tank

Figure 21

3. Remove fuel tank from the pallet.

a. Remove the mounting screws, supports, and

spacers.

b. Disconnect inlet and outlet fuel lines from the

fuel tank.

c. Use two people to lift fuel tank off of the pallet

and place where the fuel ﬁll spout is easily

accessible.

Note

Do not mount fuel tank in front of

the generator air intake or where it

will limit opening and access to the

electrical enclosure (DB).

4. Install wall (IW) where the fuel tank was located.

Ensure there is at least 1.25 in. (31.75 mm)

between the wall and exhaust mufﬂer. See

Fig. 22

Note

To prevent an air pocket from forming

inside the coolant lines between the

proportioner and generator, ensure

there is a constant rise in elevation if

the coolant lines are adjusted. Failure

to have a constant rise in elevation will

reduce heating efﬁciency. See

Fig. 23

5. Reconnect inlet and outlet fuel lines.
6. Install spacers, supports, and screws through

the fuel tank and tighten to the ﬂoor. Torque to

40 ft-lbs (54 N•m).

7. Place battery bracket over fuel tank or near the

Reactor. Remove existing battery cables from

engine and replace with the cables provided from

the fuel line and battery cable extension kit.

8. Install mounting bolts through battery bracket and

tighten to the ﬂoor. Torque to 40 ft-lbs (54 N•m).

Note

Pads under the battery bracket help

stabilize the fuel tank during operation.

332636C

Содержание Reactor 2 E-30i































































































Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды

Graco Reactor 2 E-30i, Операция

Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды