Graco Python XL-DA25 Series Скачать руководство пользователя | Manualshive

Страница: 25 / 44

background image

Repair - Pneumatic Motor

3A6831G

25

Disassemble the Pneumatic Motor

1.

Use a 10 mm socket wrench to remove the four
screws (218), and remove the pneumatic valve
(217) and gasket (216).

2.

Remove the mufflers (18).

3.

Remove the four screws (218), and remove the
manifold (215) and two gaskets (214).

4.

Use a 10 mm socket wrench to remove the pilot
valves (219), and the top and bottom covers (213
and 201).

5.

Remove the 17 mm tie bolts (210). The number of
bolts depends on your configuration.

6.

Remove the top cover (213) and the o-ring (209).

7.

Remove the shield (212) from around the
cylinder (211), and remove the cylinder.

8.

Slide the piston assembly straight up off the bottom
cover (201).

NOTE:

There is no need to take apart the piston assem-

bly. If any part is worn or damaged, the entire assembly
should be replaced.

9.

Remove the o-ring (208) from around the piston
(205).

10. Remove the retaining ring (204), u-cup seals (203),

and the o-ring (209) from the bottom cover (201).

Reassemble the Pneumatic Motor

NOTE:

For easier reassembly, start with the top

cover (213) turned over on the workbench and assem-
ble the pneumatic motor upside-down.

1.

Lubricate and install the o-ring (209) on the top
cover (213).

2.

Install the upper bumper (228) on the top cover.

3.

Lubricate the inside of the cylinder (211). Lower the
cylinder onto the top cover (213).

4.

Lubricate and install the o-ring (208) around the pis-
ton (205).

5.

Slide the piston assembly down onto the
cylinder (211). Be sure the o-ring (208) stays in
place.

6.

Install the shield (212) around the cylinder (211) and
in the groove on the top cover (213).

7.

Lubricate and install the new u-cup seal in the bot-
tom of the bearing (202) in the bottom cover (201).
The u-cup must face up and the flange face down.
See F

IG

. 21.

8.

Lubricate and install the new u-cup seal (203) in the
top of the bearing. Lips must face up.

9.

Lubricate and install the o-ring (209) in the bottom
cover (201).

10. Install the piston bumper (228) on the bottom

cover (201).

Configuration

PCI-0600-xxx-xxx-xx-x-x

PCI-0750-xxx-xxx-xx-x-x

ti12749a

ti12750a

F

IG

. 20

3*

43*

ti12755a

Lips face up

U-cup faces up.

Flange faces down.

«
...
23
24
25
26
27
...
»

Содержание Python XL-DA25 Series













































Отзывы:

Нет отзывов

Похожие инструкции для Python XL-DA25 Series

Бренд: A.O. Smith Страницы: 65

Бренд: Fedders Страницы: 4

Бренд: Garantia Страницы: 2

Бренд: Raypak Страницы: 40

Бренд: Calpeda Страницы: 32

Бренд: RainSoft Страницы: 16

VRV IV-S Series

Бренд: Daikin Страницы: 536

Бренд: Daikin Страницы: 226

Бренд: Midea Страницы: 36

ROYTRONIC A Series

Бренд: LMI Страницы: 36

Бренд: Vulcan-Hart Страницы: 40

Бренд: CLIVET Страницы: 7

Бренд: Warren rupp Страницы: 22

SCP 16000 IQ Level Sensor

Бренд: Kärcher Страницы: 76

Бренд: Garland Страницы: 100

Бренд: Slant/Fin Страницы: 16

Kaysun Aquantia R-32 PRO

Бренд: Frigicoll Страницы: 44

Бренд: Beckett Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды