Graco PRO Auto Xs Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 56

background image

Installation

8

309297K

Installation

Install the System

2 shows a typical electrostatic air spray system,

3 shows possible system options. It is not

an actual system design. For assistance in designing a
system to suit your particular needs, contact your Graco
distributor.

Warning Signs

Mount warning signs in the spray area where they can
easily be seen and read by all operators. An English
Warning Sign is provided with the gun.

Ventilate the Spray Booth

Electrically interlock the gun turbine air supply (B) with
the ventilators to prevent gun operation without ventilat-
ing fans operating. Check and follow all National, State,
and Local codes regarding air exhaust velocity require-
ments.

High velocity air exhaust will decrease the operating effi-
ciency of the electrostatic system. The minimum allow-
able air exhaust velocity is 60 ft/minute (19 linear
meters/minute).

Key to F

WARNING

Fire, Explosion, and Electric Shock Hazard

Installing and servicing this equipment
requires access to parts which may cause
electric shock or other serious injury if work
is not performed properly.

•Do not install or service this equipment
unless you are trained and qualified.

•Be sure your installation complies with
National, State and Local codes for the
installation of electrical apparatus in a Class
I, Div. I, Group D or a Group II,
Category 2G Hazardous Location.

•

Comply with all applicable local, state, and
national fire, electrical, and other safety regula-
tions.

WARNING

Flammable or Toxic Vapor Hazard

Provide fresh air ventilation to avoid the buildup of
flammable or toxic vapors when spraying, flushing, or
cleaning the gun. Do not operate the gun unless ven-
tilation fans are operating.

A

Air Hose Ground Wire

B

Graco Grounded Turbine Air Hose (TA)

C

Atomizing Air Hose, 3/8 in. (10 mm) OD (A1)

D

Fan Air Hose, 3/8 in. (10 mm) OD (A2)

E

Cylinder Air Hose, 5/32 in. (4 mm) OD (CYL)

F

Fluid Hose, 1/4-18 npsm gun fluid inlet (P1)

G

To Fluid Supply

H

Auto PRO Xs Air Spray Gun

J

Mounting Bracket for 1/2 in. (13 mm) rod

K

Solenoid Valve, requires quick exhaust port

L

Bleed-Type Master Air Valve

M

Air Pressure Regulator

N

True Earth Ground

P

24 Volt Power Supply

Q

4-20 microampere Outputs

R

Full Feature ES Display Module

S

kV Only ES Display Module (battery operated)

T

Fiber Optic Y Cable

U

Bulkhead

V

Fiber Optic Cable

W

Main Air Line

X

kV Switch Air Hose, 5/32 in. (4 mm) OD (optional; plug KV1
fitting if not used)

Y

kV Switch Air Hose, 5/32 in. (4 mm) OD (optional; plug KV2
fitting if not used)

«
...
6
7
8
9
10
...
»

Содержание PRO Auto Xs Series

























































Отзывы:

Нет отзывов

Похожие инструкции для PRO Auto Xs Series

Бренд: Graco Страницы: 32

Бренд: WAGNER Страницы: 36

SATAJet 2000 HVLP

Бренд: SATA Страницы: 29

Бренд: Smithco Страницы: 27

Бренд: Raider Страницы: 56

Бренд: Sagola Страницы: 52

Бренд: EST Страницы: 20

Бренд: Turfmate Страницы: 11

Бренд: Hardi Страницы: 100

Бренд: Power Fist Страницы: 6

Бренд: Annovi Reverberi Страницы: 44

Бренд: Nakayama Страницы: 7

Бренд: Binks Страницы: 8

Бренд: Binks Страницы: 12

WONDER WETTER Jr. 222-684

Бренд: Graco Страницы: 20

Бренд: Graco Страницы: 28

UpFront STS 14 Combo

Бренд: Hagie Страницы: 157

CONTROL PRO 250 M

Бренд: WAGNER Страницы: 144

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды