Graco PRO Auto Xs Series Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 56

background image

Repair

42

309297K

Power Supply Removal and
Replacement

•

Inspect the gun body power supply cavity for dirt or
moisture. Clean with a clean, dry rag.

•

Do not expose gasket (11) to solvents.

1.

Prepare gun for service, page 32.

2.

Remove the barrel (9), page 40.

3.

Grasp the power supply (12) with your hand. With a
gentle side to side motion, free the power sup-
ply/alternator assembly from the gun body (32),
then carefully pull it straight out. Disconnect the flex-
ible circuit (39) from the socket at the top of the body
(32). See F

4.

Disconnect the 3-wire connector (GG) from the
power supply. Slide the alternator up and off the
power supply. Inspect the power supply and alterna-
tor for damage. Disconnect the 6-pin flexible circuit
(39) from the power supply.

5.

Check the power supply resistance, page 27.
Replace if necessary.

Before installing the power supply, make sure the
o-rings (12a, 13a), spring (12b), and pads (13e) are in
place.

6.

Connect the 6-pin flexible circuit (39) to the power
supply.

7.

Connect the 3-wire connector (GG). Slide the alter-
nator (13) down onto the power supply (12).

8.

Lubricate the alternator o-ring (13a) with non-sili-
cone grease, Part No. 111265. Do not over-lubri-
cate.

9.

Lubricate the power supply o-ring (12a) with dielec-
tric grease.

10. Insert the power supply/alternator assembly in the

gun body (32). Make sure the ground strips make
contact with the body. Connect the flexible circuit
(39) to the socket at the top of the body. Push the
6-pin connector into the socket to ensure it is prop-
erly connected.

11. Install the barrel (9), page 41.

12. Test gun resistance, page 26.

CAUTION

Be careful when handling the power supply (12) to
avoid damaging it.

«
...
40
41
42
43
44
...
»

Содержание PRO Auto Xs Series

























































Отзывы:

Нет отзывов

Похожие инструкции для PRO Auto Xs Series

Бренд: Hozelock Страницы: 8

Vector AA90 79580

Бренд: Ransburg Страницы: 88

Бренд: Siegen tools Страницы: 3

Бренд: Vito Agro Страницы: 12

Бренд: Titan Tool Страницы: 84

SPEEFLO Admiral 830-331

Бренд: Titan Страницы: 40

Бренд: Titan Страницы: 28

Бренд: Titan Страницы: 104

Impact 400 Series

Бренд: Titan Страницы: 92

Бренд: Titan Страницы: 84

Бренд: Kobalt Страницы: 33

Бренд: Task Force Tips Страницы: 12

Бренд: Graco Страницы: 34

Бренд: PRETUL Страницы: 20

Бренд: BA Pumps & Sprayers Страницы: 8

Бренд: KRAFTOOL Страницы: 6

Бренд: Graco Страницы: 32

Бренд: Maruyama Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды