Graco PrecisionSwirl 243402 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 26

Graco PrecisionSwirl 243402 Скачать руководство пользователя страница 13

Service

309403R

13

Coupler Assembly Replacement

There are three ball bearing assemblies in the Preci-
sionSwirl orbital dispenser - two in the motor and one in
the motor coupling for tube support.

Only the orbiter coupling and its bearing may be
removed and replaced. If the motor bearings need to be
replaced, the entire motor requires replacement. The
tube support coupler (24) should not be removed unless
a new replacement coupler assembly is available.
Replace the complete coupler assembly, do not attempt
to replace the bearing only.

Coupler Assembly Removal

1. Place motor assembly onto the coupling support

tool. Refer to F

2. Use the push rod tool to press the bearing out of the

coupler. The push rod tool is the 4-in. piece of bar
stock included in Kit 241569. Discard the bearing.

3. Use the gear puller and coupler removal tool

included in Kit 241569 to separate the coupler from
the motor shaft. Discard the coupler. Refer to F

The repair technician must use the proper tools to
avoid damaging the bearings. Tools are provided in
bearing repair tool kit 241569.

Before removing the coupler assembly (24), you
must remove the bearing from the coupler.

Do not use the coupler removal tool to remove the
bearing.

F

IG

. 2: Coupler Assembly Removal

Push rod tool

Tube support
bearing

Coupling
support tool

Motor
assembly

TI10658_1

Orbiter coupler
assembly

Align pin in the coupler removal tool with slots in
coupler.

F

IG

. 3: Remove Orbiter Coupler

coupler
removal tool

TI10658b

Orbiter

«
...
11
12
13
14
15
...
»

Содержание PrecisionSwirl 243402



























Отзывы:

Нет отзывов