Graco Merkur 313255F Скачать руководство пользователя страница 29

Страница: 29 / 34

Kits

313255F

Kits

Wall Mount Kit 24A578

NOTE: Mounting Arms Kit 24A372 (Part 49, see page
26 or 27) also is required for wall mounting a package
that has a control panel.

Heated Cart Mount Kit 256427

102

101

ti12633a

Ref
No.

Description

Qty.

101

WALL PLATE, kit, includes screws

102

SCREW (included with 101)

201

202

209

203

207

ti13357a

206

205

204

208

----- Not sold separately.

Ref
No. Part No. Description

Qty.

201 -----

CART, frame

202 -----

HANDLE, cart

203 119451 WHEEL, semi-pneumatic

204 119452 CAP, hub

205 277790 SLEEVE, cart handle

206 15C871 CAP, leg

207 115480 KNOB, t-handle

208 116630 SCREW, carriage

209 -----

BRACKET, heater, cart

210 111799 SCREW, cap, hex head

211 104541 NUT, lock

212 115643 SCREW, hex, washer head

213 100022 SCREW, cap, hex head

214 100527 WASHER, plain

215 167002 INSULATOR, heat

210

211

215

214

213

212

Содержание Merkur 313255F



































Результаты поиска

Содержание Merkur 313255F

Отзывы:

Похожие инструкции для Merkur 313255F

Бренды по названию

Популярные бренды

Graco Merkur 313255F, Инструкция по эксплуатации

Результаты поиска

Содержание Merkur 313255F

Отзывы:

Похожие инструкции для Merkur 313255F

Бренды по названию

Популярные бренды