background image

Mixing Material

309863A

9

Mixing Material

Dry Mix - 40 lb (18 kg) bag.

1.

Slowly add one 40 lb. (18 
kg) bag of texture mate-
rial to 5-6 gallons 
(18.9-22.7 liters) of clean 
water as instructed on the 
bag instructions. 

2.

Agitate to mix, using a 
half-inch, variable speed 
drill with mixing paddle, to 
a smooth, lump-free con-
sistency.

3.

Allow ceiling texture to set 
for at least 15 minutes. 
Then remix prior to use.

4.

After texture material is thoroughly mixed, gently set 
ball end of Material Thickness Gauge on surface of 
mixture.

5.

Observe the ball on the 
material. When the mate-
rial is thin enough to spray 
the ball will sink com-
pletely into the mixture.

6.

If the ball does not sink 
completely into the mix-
ture within 10 seconds, 
add more water, agitate 
and try test again.

Premix

1.

Slowly add approxi-
mately 2 to 4 qts (1.9 to 
3.8 liters) of water to a 5 
gallon (18.9 liter) bucket 
of premix.

2.

Agitate to mix, using a 
half-inch, variable speed 
drill with a mixing pad-
dle, to a smooth, 
lump-free consistency.

3.

After texture material is thoroughly mixed, gently set 
ball end of Material Thickness Gauge on surface of 
mixture.

4.

Observe the ball in 
material. When the 
material is thin 
enough to spray the 
ball will sink com-
pletely into the mix-
ture.

5.

If the ball does not sink completely into the mixture 
within 10 seconds, add more water, agitate and try 
test again.

Correct material mixture is essential. The pump 
will not operate if the mixture is too thick.

Mix the material in a separate container before 
pouring it into hopper.

Use Material Thickness Gauge to determine 
mixture is thin enough to spray.

*The Material Thickness Gauge will only 
determine if the material is thin enough to pass 
through the pump. For some applications or for 
higher speed spraying, your mixture may need to 
be thinner.

For best results do not use partial bags of 
material.

For an accurate test, be sure gauge is completely 
dry and clean every time it is used.

ti2496

ti2497a

For an accurate test, be sure gauge is completely 
dry and clean every time it is used.

ADD WATER

READY

ti2498a

ti2493a

ADD WATER

READY

ti2498a

Содержание Magnum TexFinish 246186

















Отзывы: