manualshive.com logo in svg

Graco LineLazer IV 3900, Список запасных частей и инструкция по ремонту

Поделиться
Скачать
Graco LineLazer IV 3900 Скачать руководство пользователя страница 35

Technical Data

312195B

35

Technical Data

Loctite

®

 is a registered trademark of the Loctite Corporation.

Honda GX120 Engine (3900)

Power Rating @ 3600 rpm
ANSI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIN 6270B/DIN 6271

NA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.0 Horsepower

2.1 Kw - 2.8 Ps
2.6 Kw - 3.6 Ps

Honda GX160 Engine (5900)

Power Rating @ 3600 rpm
ANSI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIN 6270B/DIN 6271

NA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5 Horsepower

2.9 Kw - 4.0 Ps
3.6 Kw - 4.9 Ps

Maximum working pressure . . . . . . . . . . . . . . . . . . . . . . . 3300 psi (228 bar, 22.8 MPa)
Noise Level

Sound power  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sound pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

105 dBa, per ISO 3744
96 dBa, measured at 3.1 feet (1 m)

*Vibration Level

LineLazer IV 3900

Left hand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Right hand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LineLazer IV 5900

Left hand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Right hand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

* Vibration measured per ISO 5349 based on 8 hour daily 
exposure

1.81 m/sec

2

1.45 m/sec

2

2.05 m/sec

2

1.70 m/sec

2

Maximum delivery

LineLazer IV 3900  . . . . . . . . . . . . . . . . . . . . . . . . . . .
LineLazer IV 5900  . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.15 gpm (4.4 liter/min)
1.5 gpm (5.7 liter/min)

Maximum tip size

LineLazer IV 3900  . . . . . . . . . . . . . . . . . . . . . . . . . . .

LineLazer IV 5900  . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 gun with 0. 034 in. tip
2 guns with 0.024 in. tip
1 gun with 0. 041 in. tip
2 guns with 0.028 in. tip

Inlet paint strainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 mesh (1190 micron) stainless steel screen, reusable
Outlet paint strainer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 mesh (250 micron) stainless steel screen, reusable
Pump inlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/4 in. npt (m)
Fluid outlet size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 npsm from fluid filter
Wetted parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . nickel-plated carbon steel, PTFE, Nylon, polyurethane, 

UHMW polyethylene, fluoroelastomer, acetal, leather, 
tungsten carbide, stainless steel, chrome plating

Содержание LineLazer IV 3900







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды