background image

 

Accessories

USE GENUINE GRACO PARTS AND ACCESSORIES

AIR LINE LUBRICATOR

250 psi (17.5 bar) MAXIMUM WORKING PRESSURE

214-848  1/2 npt inlet and outlet

214-849  3/4 npt inlet and outlet

AIR LINE FILTER

250 psi (17.5 bar) MAXIMUM WORKING PRESSURE

106-149  1/2 npt inlet and outlet

106-150  3/4 npt inlet and outlet

STAINLESS STEEL AIRLESS SPRAY GUN

5000 psi (350 bar) MAXIMUM WORKING PRESSURE

208-327

.037” orifice, 2-finger trigger

208-663

.090” orifice, 2-finger trigger

208-664

.090” orifice, 4-finger trigger

220-954

.090” orifice, 2-finger trigger, 

RAC

t

 IV DripLess

t

 tip guard

GROUNDED BUNA-N AIR SUPPLY HOSE

175 psi (12 bar) MAXIMUM WORKING PRESSURE

Part No.

ID

Length

Thd. Size

205-418

1/2” (13 mm)

6 ft (1.8 m) 

1/2 npt(m)

205-216

1/2” (13 mm)

15 ft (4.5 m)

1/2 npt(m)

205-273

1/2” (13 mm)

25 ft (7.6 m)

1/2 npt(m)

208-594

1/2” (13 mm)

50 ft (15 m)

1/2 npt(m)

BACK PRESSURE REGULATOR 206-819

3000 psi (210 bar) MAXIMUM WORKING PRESSURE

Use in circulating system fluid return line to regulate back

pressure to gun and maintain proper circulating pres-

sure.

FLUID PRESSURE REGULATOR 206-661

3000 psi (210 bar) MAXIMUM WORKING PRESSURE

Use at each gun drop in multiple gun systems, to regulate

fluid pressure to each gun.

GROUNDED NYLON FLUID HOSE

3000 psi (210 bar) MAXIMUM WORKING PRESSURE

Part No.

ID

Length

Thd. Size

214-700

3/16” (4.8 mm)

2 ft (610 mm)

1/4 npsm 

(fbe) swivel

214-701

3/16” (4.8 mm)

3 ft (914 mm)

1/4 npt(m) 

x 1/4 

npsm(f) 

swivel

223-540

1/4” (6.4 mm)

25 ft (7.6 m)

1/4 npsm

 

(fbe) swivel

223-541

1/4” (6.4 mm)

50 ft (15.2 m) 

1/4 npsm 

(fbe) swivel

214-703

3/8” (9.5 mm)

25 ft (7.6 m)

3/8 npt 

(mbe)

214-705

3/8” (9.5 mm)

50 ft (15.2 m) 

3/8 npt 

(mbe)

214-920

3/8” (9.5 mm)

100 ft (30.4 m)

3/8 npt 

(mbe)

INSULATED HOSE KIT 222-263

3000 psi (210 bar) MAXIMUM WORKING PRESSURE

25 ft. (7.6 m) nylon fluid hose for use with heated sys-

tems. Includes in-line fluid filter, circulating manifold, and

3 ft. (0.9 m) whip hose.

VISCON

@

 FLUID HEATER

4000 psi (276 bar) MAXIMUM WORKING PRESSURE

Specify desired voltage when ordering (see below).

Heater reduces fluid viscosity for easier spraying. Stain-

less steel. Refer to Instruction Manual 307-805.

Model 220-522 (120 V, single-phase, 16.7 Amp)

Model 220-523 (240 V, single-phase, 9.6 Amp)

Model 220-524 (480 V, single-phase, 4.8 Amp)

VISCON

@

 HEATER CORD 110-160

12 gauge, rated at 105

_

 C.

WARNING: Not for use in  hazardous areas containing

flammable materials or fumes.

HEATER CONVERSION KITS

Use to convert pump Model 222-268 to a heated spray

system. See pages 16 and 17 for parts. Viscon

@

 Heater

must be ordered separately. 

222-269

Heater Mounting Kit

222-270

Circulating Kit

SST PIPE SEALANT 110-110

Apply to all non-swiveling pipe connections.

6 ml supply.

Содержание HYDRA-SPRAY President A Series





















Отзывы: