Graco Husky 515 D51 Series Скачать руководство пользователя | Manualshive

Страница: 4 / 38

background image

4 308981

Installation

General Information

•

The Typical Installations in

are only guides for

selecting and installing system components.
Contact your Graco distributor for assistance in
planning a system to suit your needs.

•

Always use Genuine Graco Parts and Accessories.

•

Use a compatible, liquid thread sealant on all male
threads. Tighten all connections firmly to avoid air or
fluid leaks.

Tightening Threaded Fasteners Before First
Use

Before using the pump for the first time, check and

retorque all external fasteners. See

Torque Sequence

page 29. After the first day of operation, retorque the

fasteners. Although pump use varies, a general guide-

line is to retorque fasteners every two months.

Toxic Fluid Hazard

Use fluids and solvents that are compatible with the

equipment wetted parts. Refer to the Technical Data

section of all equipment manuals. Read the fluid and

solvent manufacturer’s warnings.

Mountings

•

These pumps can be used in a variety of
installations. Be sure the mounting surface can
support the weight of the pump, hoses, and
accessories, as well as the stress caused during
operation.

•

shows some installation examples. On all

installations, mount the pump using screws and
nuts.

•

Prolonged exposure to UV radiation will degrade
natural polypropylene components of the pumps. To
prevent potential injury or equipment damage, do
not expose pump or the plastic components to direct
sunlight for prolonged periods.

Pumping High-Density Fluids

High density fluids may prevent the lighter non-metallic

check valve balls from seating properly, which reduces

pump performance significantly. Stainless steel balls

should be used for such applications.

Split Manifolds

Plastic Split Manifold Kits are available to enable you to

pump two fluids simultaneously or to mix two fluids in

the pump. To order a Split Manifold Kit, use the Part No.

from the list below:

241240

polypropylene; split inlet

241241

acetal; split inlet

241242

PVDF; split inlet

241243

polypropylene; split outlet

241244

acetal; split outlet

241245

PVDF; split outlet

TOXIC FLUID HAZARD

on page

CAUTION

Safe Operating Temperatures
Minimum (all pumps): 40°F (4°C)
Maximum
Acetal: 180°F (82°C)
Polypropylene: 150°F (66°C)
Aluminum, stainless steel, PVDF: 225°F (107°C)
These temperatures are based upon mechanical stress
only and may be significantly altered by pumping cer-
tain chemicals. Consult engineering guides for chemi-
cal compatibilities and temperature limits, or contact
your Graco distributor.

«
...
2
3
4
5
6
...
»

Содержание Husky 515 D51 Series







































Отзывы:

Нет отзывов

Похожие инструкции для Husky 515 D51 Series

Бренд: Danfoss Страницы: 34

Бренд: Danfoss Страницы: 52

Бренд: Zehnder Pumpen Страницы: 32

Signature XP19-024

Бренд: Lennox Страницы: 32

Бренд: IMO Страницы: 24

Бренд: Nagman Страницы: 15

Бренд: U.S. Products Страницы: 8

2JT Cartridge EV9608-10

Бренд: Everpure Страницы: 2

Бренд: AQUASYSTEM Страницы: 12

Serve Better CP-RP

Бренд: Server Страницы: 8

Бренд: OilGear Страницы: 31

Бренд: Enertech Страницы: 40

Бренд: Wayne Страницы: 1

Бренд: Drazice Страницы: 28

Blue Diamond MaxiBlue

Бренд: Charles Austen Страницы: 20

HydroTap 30009UK

Бренд: Zip Страницы: 24

Бренд: CME Страницы: 28

E1+P GI 11,4 T SD

Бренд: DAB Страницы: 184

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды