Graco Husky 3300 Скачать руководство пользователя

Страница: 18 / 42

Repair

3A0411A

All Other Standard Diaphragms - Metal Pumps:

1. Install the washer (18) and o-ring (17) on the shaft

bolt (16).

2. Assemble the fluid side plate (15), the diaphragm

(20), the air side diaphragm plate (14), and the
washer (18) on the bolt exactly as shown in F

. 6.

3. Apply medium-strength (blue) Loctite or equivalent

to the bolt (16) threads. Screw the bolt into the shaft
hand tight.

4. Grease the shaft u-cups (101*) and the length and

ends of the diaphragm shaft (108*). Slide the shaft
into the housing.

5. Repeat Steps 1-5 for the other diaphragm assem-

bly.

6. Hold one shaft bolt with a wrench and torque the

other bolt to 110-120 ft-lb (149-163 N•m) at 100 rpm
maximum. Do not over-torque.

7. Reattach one fluid cover (2). Arrow (A) must point

toward the air valve. See

Torque Instructions,

page 20.

TP, SN, and GE Models:

Follow directions under

Attach Second Fluid Cover

, page 19.

CR, BN, and FK Models:

Reattach the second fluid

cover (2). Arrow (A) must point toward the air valve.
See

Torque Instructions,

page 20.

9. Reassemble the ball check valves and manifolds as

explained on page 12.

All Other Standard Diaphragms - Plastic Pumps:

1. Assemble the diaphragm (20), the air side dia-

phragm plate (14), and the washer (18) on the fluid
side plate (15) exactly as shown in F

. 6.

2. Apply medium-strength (blue) Loctite or equivalent

to the threads of the screw on the fluid side plate.
Screw the assembly into the shaft hand-tight.

3. Grease the shaft u-cups (101*) and the length and

ends of the diaphragm shaft (108*). Slide the shaft
into the housing.

4. Repeat for the other diaphragm assembly.

5. Hold one of the plates with a wrench, and torque the

other plate to 110-120 ft-lb (149-163 N•m) at 100
rpm maximum. Do not over-torque.

6. Reattach one fluid cover (2). Arrow (A) must point

toward the air valve. See

Torque Instructions,

page 20.

TP, SN, and GE Models:

Follow directions under

Attach Second Fluid Cover

, page 19.

CR, BN, and FK Models:

Reattach the second fluid

cover (2). Arrow (A) must point toward the air valve.
See

Torque Instructions,

page 20.

8. Reassemble the ball check valves and manifolds as

explained on page 12.

Содержание Husky 3300











































Результаты поиска

Содержание Husky 3300

Отзывы:

Похожие инструкции для Husky 3300

Бренды по названию

Популярные бренды

Graco Husky 3300, Запасные части

Результаты поиска

Содержание Husky 3300

Отзывы:

Похожие инструкции для Husky 3300

Бренды по названию

Популярные бренды