Graco GrindLazer 25P474 Скачать руководство пользователя страница 30

Страница: 30 / 74

Troubleshooting

3A7600C

Troubleshooting

Gas/Propane:

To avoid injury from unexpected start

up, disable engine as follows: 1) Turn ignition OFF. 2)
Disconnect spark plug wires. 3) Disconnect negative
(-) battery cable from battery.

Electric:

To avoid injury from unexpected start up,

disconnect power plug before you service your
machine.

Electric:

To avoid injury from unexpected movement,

ensure Power Switch is in the OFF position before
connecting or disconnecting the power cord. In the
event of a power failure or interruption, ensure Power
Switch is in the OFF position before restoring power.

Problem

Cause

Solution

Cutters wearing unevenly/prema-
turely

Cutter head is too low

Raise the cutter head

Material build up

Clean the cutters

Bearings may be worn

Replace bearings

Wrong cutters for application

Contact Tech Services

Cutters Shaft Breakage
unevenly/prematurely

Cutter head is too low

Raise the cutter head

Over 40 hours service life

Replace shafts

Drum wearing prematurely or

cracking

Drum hitting work surface

Raise the drum

Shafts and bushings not replaced within 40
hours

Replace shafts and bushings

Excess Vibration

Bearings may be worn

Replace bearings

Drive shaft worn

Replace drive shaft

Improper cutter set-up

Contact Tech Services

Spindle contacting the work surface

Raise the cutter head

Wheels worn out

Replace the wheels

Machine jumps erratically

RPM is too low

Turn engine throttle or speed control to
highest setting

Work surface is severely uneven

Move to smoother work surface

Содержание GrindLazer 25P474











































































Результаты поиска

Содержание GrindLazer 25P474

Отзывы:

Бренды по названию

Популярные бренды

Graco GrindLazer 25P474, Операция - Ремонт - Запчасти

Результаты поиска

Содержание GrindLazer 25P474

Отзывы:

Бренды по названию

Популярные бренды