manualshive.com logo in svg

Graco GrindLazer 25M842, Операция - Ремонт - Запчасти

Поделиться
Скачать
Graco GrindLazer 25M842 Скачать руководство пользователя страница 10

Setup 

10

3A5578C

4. Slide out drum assembly (use caution as it is 

heavy).

5. Once the cutter drum is removed take to a 

workbench for assembly.

a. Inspect condition of cutters, spacers, shafts, 

bushings and drum.

6. Before replacing the drum onto hex shaft:

a. Check that all bearings are in good working 

order.

b. Remove dirt and material build-up from inside 

drive carriage and drum.

c. Lube all metal contacts.

7. Align and slide drum back onto the hex shaft.

8. Replace Drum Access Panel (lift up and lock into 

place) over hex shaft and secure hardware.

NOTE: An extra drum loaded with cutters for rapid job 
site replacement is recommended. 

Vacuum Attachment 

1. If using a vacuum, attach vacuum hose to the 

Vacuum Port. 

2. Attach vacuum hose to the Inlet Port on the Cyclone 

Separator (optional) or vacuum. \

Содержание GrindLazer 25M842





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды