Graco GM 3500 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 44

background image

9

307-863

Setup

5.

Check the engine oil level. Refer to the Honda
engine manual, supplied. This is a summary of the
information: Remove one of the oil fill plugs; (C)
the oil should be almost overflowing. See Fig. 2.
Add oil as necessary.

Recommended lubrication oil: Use a high–quality,
detergent oil, SAE 10W–40, classified “FOR
SERVICE SE or SF”, for regular use and for
breaking–in a new engine.

6.

Be sure your system is properly grounded be-
fore operating it. Read and follow the warning
section, Fire Or Explosion Hazard, page 3. Use
the ground wire (47) provided.

7.

Fill the gas tank. See the Fueling section, below.

8.

Flush the pump to remove the lightweight oil
which was left in the pump to protect it from rust.
Refer to the Flushing, page 12.

9.

Prepare the paint according to the manufacturer’s
recommendations. Remove any skin that may
have formed. Stir the paint to mix pigments.

10. Strain the paint through a fine nylon mesh bag

(available at most paint dealers) to remove par-
ticles that could clog the filter or spray tip. This is
probably the most important step toward trouble–
free spraying.

11. Keep the sprayer upright and level during oper-

ation and whenever it is being moved. Read the
last CAUTION on page 10.

A

Fig. 2

47

B

C

Fueling

WARNING

Gasoline is extremely flammable and explosive
under certain conditions. To reduce the risk of a fire
or explosion:

Always shut off the engine (B) before refueling.

Refuel in a well–ventilated area.

Do not smoke or allow flames or sparks in the
area where the engine is refueled or where the
gasoline is stored.

Do not overfill the tank. Make sure the filler cap
is securely closed after refueling.

Be careful not to spill fuel when fueling. Fuel
vapor or spilled fuel can ignite. If any fuel is
spilled, make sure the area is dry before starting
the engine.

1.

Fuel specifications. Use automotive gasoline
with a pump octane number of 86 or higher. If the
engine knocks or pings, use a higher octaine gaso-
line. Unleaded fuel minimizes combustion chamber
deposits.

2.

Gasolines containing alcohol (gasohol). Do not
use gasohol which contains methanol, if the gaso-
hol does not contain cosolvents and corrosion inhi-
bitors for methanol. Even if it does contain such
additives, do not use the gasohol if it contains
more than 5% methanol.

NOTE: The HONDA engine warranty does not cover
damage resulting from the use of gasolines containing
alcohol. See the HONDA engine manual for more in-
formation.

3.

General. Do not use oil and gasoline mixtures or
contaminated gasoline. Avoid getting dirt, dust or
water in the fuel tank.

4.

Tank Capacity. 0.66 gallons (2.5 liter). Always
leave at least 1/2 in. at the top of the tank for
expansion.

5.

Shut off the engine before refueling.

6.

After refueling, tighten the fuel tank cap (A)
firmly.

«
...
7
8
9
10
11
...
»

Содержание GM 3500













































Отзывы:

Нет отзывов

Похожие инструкции для GM 3500

Бренд: NEC Страницы: 54

medialon Showmaster Go

Бренд: 7th Sense Страницы: 9

Бренд: A&D Страницы: 2

Бренд: A&D Страницы: 176

Бренд: ICP DAS USA Страницы: 45

Бренд: iFIT Страницы: 11

Бренд: K-9 Lights Страницы: 12

Бренд: Labelmate Страницы: 61

Бренд: Labconco Страницы: 62

Бренд: M-Audio Страницы: 3

Бренд: Naked Страницы: 36

9NP-B7524 Series

Бренд: Nautilus Страницы: 2

Be strong NS 700X

Бренд: Nautilus Страницы: 34

Бренд: Nautilus Страницы: 21

Бренд: Nellcor Страницы: 161

OXIMAX N-600X Series

Бренд: Nellcor Страницы: 210

Бренд: OAKWORKS Страницы: 24

Бренд: Össur Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды