Graco GM 3500 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 44

background image

Accessories

USE ONLY

GENUINE GRACO

PARTS AND ACCESSORIES

French

185–956

Spanish

185–961

German

186–041

Greek

186–045

Korean

186–049

English

185–953

Apply other
language here

DANGER LABELS

The English language DANGER label shown on
page 1 is also on your sprayer. If you have paint-
ers who do not read English, order one of the fol-
lowing labels to apply to your sprayer. The drawing
below shows the best placement of these labels
for good visibility.
Order the labels directly from Graco, free of
charge.

Toll Free:

1–800–328–0211

SUCTION TUBE KIT

208–920

5 gallon (19 liter) size, For Upright Cart Sprayers
Includes:

Ref
No.

Part No.

Description

Qty

1

101–818

CLAMP, hose

2

2

160–327

UNION, 90

swivel; 3/4 npt(m x f)

1

3

170–705

ADAPTER, intake

1

4

170–706

HOSE, 1” ID x 48”; nylon

1

5

170–957

TUBE, suction

1

6

181–072

STRAINER

1

1

5

6

2

3

1

4

SUCTION TUBE KIT

208–259

55 gallon (200 liter) size, For Upright Cart Sprayers
Includes:

Ref
No.

Part No.

Description

Qty

1

156–589

UNION, 90

ADAPTER, 3/4 npt(f) x

3/4 np(f) swivel

1

2

214–961

HOSE, coupled 3/4 npt(mbe)
3/4” ID; nylon, 6 ft (1.8 m);
spring guard one end

1

3

156–591

ELBOW, 90

; 3/4 npt x 1–1/2 – 24 NS 1

4

156–593

PACKING, o–ring, nitrile rubber

1

5

100–220

THUMBSCREW, 5/16–18 x 1”

1

6

176–684

ADAPTER, bung

1

7

156–592

TUBE, riser

1

8

159–100

RETAINER, screen

1

9

161–377

SCREEN, filter

1

10

159–101

NUT, screen retainer

1

1

2

7

8
9

10

5

6

Ä

Ä

3

4

DISPLACEMENT PUMP REPAIR KIT

222–588

See contents on page 35. Repair instructions are in-
cluded with the kit.

SLEEVE REMOVAL TOOL

222–586

Required for removing the sleeve of the displacement
pump during service.

THROAT SEAL LIQUID

Non–evaporating liquid for the wet–cup. Helps prevent
buildup of paint on the rod and throat packings, to re-
duce premature wear.

206–994

8 oz.

206–995

1 quart

206–996

1 gallon

«
...
36
37
38
39
40
...
»

Содержание GM 3500













































Отзывы:

Нет отзывов

Похожие инструкции для GM 3500

Бренд: Hagie Страницы: 61

Бренд: JackJaw Страницы: 2

Бренд: Wavetek Страницы: 74

Бренд: Fairchild Страницы: 16

Бренд: Cambridge Audio Страницы: 2

Бренд: Warehouse-lighting Страницы: 3

Бренд: Eagle Group Страницы: 8

Бренд: E2S Страницы: 5

Бренд: Keller Страницы: 12

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 4

Бренд: Nederman Страницы: 255

Бренд: Fast Страницы: 60

Бренд: mychway Страницы: 56

i-Digits Access

Бренд: Össur Страницы: 231

Бренд: Qtx Страницы: 6

Бренд: Onwa Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды