Graco Fast-Ball 222051, Инструкция по эксплуатации

Страница: 6 / 18

Installation
6 307906ZAA
• Air and Fluid Hose Kits (F): An 18-inch kit for wall
mounted pumps and a 6-foot kit for drum-mounted
pumps are available. Use a minimum 1/4-inch ID air
supply hose between the pump air inlet and the air
accessories. To order a kit with a 1/4-inch air hose,
1/4-inch swivel elbow, 3/4-inch fluid hose, and
3/4-inch swivel elbow, order one of the following kits:
- 222118 - 18-inch (0.4 m) hose kit for wall
mounted pump.
- 222119 - 6-foot (1.8 m) hose kit for drum
mounted pump.
• Wall Bracket (J): The wall bracket is used for
mounting the Universal pump. The wall bracket is
sized to fit any Graco pump designed to use a
2-inch bung adapter. Order Part No. 203987.
• Runaway Valve: Install a pump runaway valve to
shut off the air to the pump when the pump acceler-
ates beyond the pre-adjusted setting. A pump that is
in a runaway condition can be seriously damaged.
• Bleed-Type Master Air Valve (E): Install a
bleed-type master air valve to relieve air trapped
between it and the motor when the valve is closed.
A 300 psi (2.1 Mpa, 21 bar), 1/4-inch npt(f) bleed
type master air valve is available from Graco. Order
Part No. 110223.
• Suction Kit (L): The suction kit is for use with the
wall-mounted Universal pump. It includes a drum
tube and hose. Order Part No. 213099.
• Air Motor Lubricator (D): The air motor lubricator
provides automatic air motor lubrication. A 250 psi
(1.7 MPa, 17.4 bar), 1/4-inch npt(f) air motor lubrica-
tor is available from Graco. Order Part No. 110148.
• Air Regulator and Gauge (C): The air regulator
and gauge are used to control air pressure and
pump speed. A 0-200 psi (0-1.4 MPa, 0-14 bar) reg-
ulated pressure range 300 psi (2.1 MPa, 21 bar)
maximum, 1/4-inch npt(f) air regulator and gauge
are available from Graco. Order Part No. 110147.
• Air Filter (B): The air filter removes harmful dirt and
moisture from the compressed air supply. A 300 psi
(2.1 MPa, 21 bar), 1/4-inch npt(f) air filter (20
micron) is available from Graco. Order Part No.
110146.
• Air and Fluid Shutoff Valves (A and H): Install air
shutoff valve (A) and fluid shutoff valve (H) as
shown in F
IG
. 1, page 4, to isolate the pump while
you are servicing it.
• Quick-Disconnect Coupler and Nipple: The
quick-disconnect coupler and nipple (not shown) are
used to quickly disconnect the air supply. Attach the
coupler (Part No. 208536) to the pump air inlet
hose, and install the nipple (Part No. 169970) to the
pump air inlet (P).
• Thermal Relief Kit: Install the thermal relief kit on
the dispensing valve side of the pump to assist in
relieving pressure in the pump, hose and dispensing
valve due to heat expansion. A 600 psi (4.2 MPa, 41
bar) thermal relief kit is available from Graco. Order
Part No. 237601.
NOTICE
Never allow the pump to run dry of the fluid being
pumped. A dry pump quickly accelerates to a high
speed, possibly damaging itself, and it may get very
hot.