Graco Endura-Flo 4D150 Скачать руководство пользователя страница 40

Страница: 40 / 42

Technical Specifications

Technical Speciﬁcations

Metric

Maximum air input pressure

100 psi

7 bar, 0.7 MPa

Maximum inlet feed pressure*

70 psi

4.8 bar, 0.48 MPa

Maximum ﬂuid working pressure

400 psi

28 bar, 2.8 MPa

Maximum static ﬂuid pressure

430 psi

30 bar, 3.0 MPa

Ratio

4:1

Maximum recommended continuous

cycle rate

20 cycles per minute

Volume per cycle (double stroke)

4D150

5 oz per cycle

150 cc per cycle

4D350

12 oz per cycle

350 cc per cycle

Ambient and operating temperature

range. Use dry compressed air when

operating at low temperatures.

32 to 122°F

0 to 50°C

Dry suction lift

23 ft

7.0 m

Wet suction lift

29 ft

8.8 m

Air inlet size

4D150

1/4 npt

4D350

1/2 npt

Fluid inlet size

4D150

1 in. Tri-Clamp Flange, 1/2 in npt, or 1/2 in bspp

4D350

1 in. Tri-Clamp Flange, 3/4 in npt, or 3/4 in bspp

Fluid outlet size

4D150

1 in. Tri-Clamp Flange, 1/2 in npt, or 1/2 in. bspp

4D350

1 in. Tri-Clamp Flange, 3/4 in npt, or 3/4 in. bspp

Weight (approximate)

4D150

31 lb

14 kg

4D350

72 lb

33 kg

Wetted parts

stainless steel, perﬂuoroelastomer (FFKM), PTFE, Polyphenylene

Sulﬁde (PPS)

* NOTE: When pressure feeding the pump inlet, do not allow the outlet pressure to exceed the Maximum

Fluid Working Pressure. The inlet feed pressure will pressurize the outlet by the corresponding amount.
Example: Pressure feeding the inlet with 60 psi and supplying 80 psi air pressure will result in the following:

80psi*4:1+60psi = 380psi ﬂuid pressure.

333015E

Содержание Endura-Flo 4D150











































Результаты поиска

Содержание Endura-Flo 4D150

Отзывы:

Похожие инструкции для Endura-Flo 4D150

Бренды по названию

Популярные бренды

Graco Endura-Flo 4D150, Инструкция - Каталог запасных частей

Результаты поиска

Содержание Endura-Flo 4D150

Отзывы:

Похожие инструкции для Endura-Flo 4D150

Бренды по названию

Популярные бренды