Graco Check-Mate 2100 A Series Скачать руководство пользователя страница 1

Страница: 1 / 38

Instructions – Parts List

GRACO INC.

P.O. BOX 1441

MINNEAPOLIS, MN

55440–1441

CARBON STEEL

Check–Mate

2100 Pumps

With Priming Piston, and Severe–Duty Rod and Cylinder

Part No. 222828 Pump, Series A
Part No. 246935 Pump, Series A

12:1 Ratio, with Bulldog

Air Motor

8.3 MPa, 83 bar (1200 psi) Maximum Fluid Working Pressure
0.7 MPa, 7 bar (100 psi) Maximum Air Input Pressure

Part No. 222829 Pump, Series A

12:1 Ratio, with Quiet Bulldog

Air Motor

8.3 MPa, 83 bar (1200 psi) Maximum Fluid Working Pressure
0.7 MPa, 7 bar (100 psi) Maximum Air Input Pressure

Part No. 222835 Pump, Series A
Part No. 246936 Pump, Series A

24:1 Ratio, with King

Air Motor

16.6 MPa, 166 bar (2400 psi) Maximum Fluid Working Pressure
0.7 MPa, 7 bar (100 psi) Maximum Air Input Pressure

Part No. 222901 Pump, Series B

24:1 Ratio, with Quiet King

Air Motor

16.6 MPa, 166 bar (2400 psi) Maximum Fluid Working Pressure
0.7 MPa, 7 bar (100 psi) Maximum Air Input Pressure

Part No. 222940 Pump, Series A

39:1 Ratio, with Premier

Air Motor

26.9 MPa, 269 bar (3900 psi) Maximum Fluid Working Pressure
0.7 MPa, 7 bar (100 psi) Maximum Air Input Pressure

Part No. 222902 Pump, Series B
Part No. 246937 Pump, Series A

with Viscount

Hydraulic Motor

15.9 MPa, 159 bar (2300 psi) Maximum Fluid Working Pressure
10 MPa, 103 bar (1500 psi) Maximum Hydraulic Input Pressure

308149P

Important Safety Instructions

Read all warnings and instructions in this manual.
Save these instructions.

See page 2 for

Table of Contents

Part No.

222835
Shown

Parts

Содержание Check-Mate 2100 A Series







































Результаты поиска

Содержание Check-Mate 2100 A Series

Отзывы:

Похожие инструкции для Check-Mate 2100 A Series

Бренды по названию

Популярные бренды

Graco Check-Mate 2100 A Series, Инструкция-перечень запасных частей

Результаты поиска

Содержание Check-Mate 2100 A Series

Отзывы:

Похожие инструкции для Check-Mate 2100 A Series

Бренды по названию

Популярные бренды