background image

Installation

3A8693B

9

Accessories

Install the following accessories in the order shown in 
F

IG

. 1, using adapters as necessary.

Air Line

Bleed-type master air valve (B): required in your 
system to relieve air trapped between it and the air 
motor when the valve is closed.

Be sure the valve is easily accessible from the 
equipment and located downstream from the air 
regulator.

Air regulator (C): to control pump speed and fluid 
outlet pressure. Locate it close to the equipment.

Air line filter (F): removes harmful dirt and moisture 
from compressed air supply.

Master bleed-type air valve (E): isolates air line 
accessories for servicing. Locate upstream from all 
other air line accessories.

1.

Install the air line accessories as shown in F

IG

. 1. 

Verify that the air line supplying the accessories is 
grounded.

2.

Install a conductive, flexible air line (A) between the 
accessories and the 3/4 npt(f) air inlet (N). Use a 
minimum 1/2 in. (13 mm) inner-diameter air line.

Fluid Supply and Outlet Lines

Fluid drain valve (J): required in your system, 
relieves fluid pressure in the fluid line.

Fluid pressure relief valve (V): relieves fluid 
pressure in the fluid line. See F

IG

. 5.

Fluid shutoff valve (K): shuts off fluid flow.

1.

Install flexible, conductive fluid lines (G and L). 

2.

Install a fluid drain valve (J) in the fluid outlet line (L) 
close to the fluid outlet. See F

IG

. 1.

3.

Install a fluid shutoff valve (K) in the fluid outlet line 
(L) downstream from the fluid drain valve (J).

4.

If needed, install a fluid pressure relief valve (V). 
See Fluid Pressure Relief Valve, page 11.

NOTE: For best results, always install the pump as 
close as possible to the material source. See the 
Technical Specifications, page 32, for maximum 
suction lift (wet and dry). 

A bleed-type master air valve (B) is required in the 
system to relieve air trapped between this valve and 
the equipment. Trapped air can cause the equipment 
to cycle unexpectedly, which could result in serious 
injury, including splashing in the eyes or on the skin. 
See F

IG

. 1.

A fluid drain valve (J) is required to relieve pressure in 
the fluid outlet line. The drain valve reduces the risk of 
serious injury, including splashing in the eyes or on 
the skin, when relieving pressure.

NOTICE

The equipment can be damaged if flexible fluid lines 
are not used. If hard-plumbed fluid lines are used in 
the system, use a short length of flexible, conductive 
fluid line to connect to the equipment.

Содержание Aluminum Husky 2150 LP



































Отзывы: