Graco 3A8693C Скачать руководство пользователя страница 16

Страница: 16 / 34

Repair

3A8693C

Repair

Repair kits available to purchase separately. Use all parts in the kits for best results. See

Parts

, starting on page 25.

Check Valve Repair

Tools Required:

• Torque wrench

• 4 mm hex key

• 15 mm socket wrench
See

Kits and Accessories

, page 28, for available

repair kits. Service the check valves as follows.

See F

. 6.

Disassemble Check Valves

1. Perform the

Pressure Relief Procedure

, page 12.

2. Disconnect all air and fluid lines from the

equipment.

3. Remove clevis and cotter pins (126, 127) from

manifolds (102, 103).

4. Remove bolts (120).
5. Remove manifolds from fluid covers (101).

NOTE:

Use care while removing manifolds to avoid

damage to check valve components.

6. Remove all check valve components and gaskets

(121).

NOTE:

Pay attention to the orientation of the check

valve components for reassembly.

7. Clean and inspect all parts for wear or damage.

Replace as needed.

NOTE:

To ensure proper seating, always replace all

gaskets, seats, and check valve components when

performing check valve repairs.

Reassemble Check Valves

1. Install all check valve components in the correct

orientation. See F

. 6.

NOTE:

Ensure that the check valves and seating

areas are clean.

NOTE:

Install the flapper valves with the solid

rubber side facing toward the seat.

2. Install gaskets (121) onto the outer diameter of the

center manifolds (113).

NOTE:

Before reassembling manifolds, grease both

surfaces of the gasket (121) and the mating inner

diameter of the manifolds (102, 103).

NOTE:

Always replace the manifold gaskets (121)

when repairing the equipment.

3. Align manifolds (102, 103) with the fluid covers

(101) and center manifold (113).

4. Simultaneously connect the manifolds (102, 103) to

the joints at the fluid cover (101) and center

manifold (113).

NOTE:

For proper installation, ensure that the

manifold joints are connected at the same time.

5. Insert screws (120) and torque. See

Torque

Sequence

, page 29.

6. Reconnect air and fluid lines to equipment.

Содержание 3A8693C



































Результаты поиска

Содержание 3A8693C

Отзывы:

Похожие инструкции для 3A8693C

Бренды по названию

Популярные бренды

Graco 3A8693C, Инструкция по эксплуатации

Результаты поиска

Содержание 3A8693C

Отзывы:

Похожие инструкции для 3A8693C

Бренды по названию

Популярные бренды