Graco 25M449 Скачать руководство пользователя страница 6

Страница: 6 / 20

TLM Display

3A5411J

Configure the TLM

Press the Display button (A) again to
configure the TLM with a new profile.

The display reads CONFIG OK, as
shown in F

. 4, page 6, after the TLM is

configured with the new profile.

If the TLM was not configured with a new
profile by the Pulse software, the error
message CONFIG E8 displays (Step 2,
F

. 4).

TLM Registration Process

Step 1: Connect Device

Step 2: Load Initial Profile

TLM Display

Registration

Displays REGISTER. Successful registration
adds a second line: OK. Registration failure
adds a second line: ERROR.

Profile

Displays CONFIG. Successful TLM
configuration adds a second line OK.
Unsuccessful TLM configuration adds a
second line ERROR.

Measurement Reporting

Displays REPORT. If data is successfully
transmitted, adds a second line OK. If data is
not successfully transmitted, adds a second
line ERROR.

Sensor Communication Error

If the sensor does not respond to commands
before timeout, a communication error is
flagged. Displays COMM ERR.

Bad Measurement

If there is a communication error during a
read measurement (i.e., timeout), or the
status from the read measurement command
indicates there is an issue, SENSOR ERR #
is displayed. The # corresponds to the
following Sensor Error Table.

SENSOR ERROR TABLE

. 3

. 4

Error

Description

Sensor E0

Invalid reading or sensor
communication error

Sensor E1

No sensor PCBA detected
(damaged circuit board)

Sensor E4

Invalid profile parameter

Sensor E5

Measurement exceeds maximum
length

Sensor E7

Registration error

Sensor E8

Profile error

Sensor E9

RF communication error (no
acknowledge or no signal)

Содержание 25M449





















Результаты поиска

Содержание 25M449

Отзывы:

Похожие инструкции для 25M449

Бренды по названию

Популярные бренды

Graco 25M449, Инструкция по эксплуатации

Результаты поиска

Содержание 25M449

Отзывы:

Похожие инструкции для 25M449

Бренды по названию

Популярные бренды