Graco 25C528 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 48

background image

Angled

Angled

Angled Adapter

Adapter

Adapter 16H294

16H294

16H294 —

—

— Model

Model

Model 25C530

25C530

25C530

only

only

only

If the agitator is used on a drum with an off-center
bung and the blades contact the side of the drum, the
angled adapter 16H294 must be used.

1.

Thread the locking ring (28) onto the angled
adapter (27) by hand, as far as it will go.

2.

Thread the angled adapter into the bung until
it bottoms out, then back it out until the widest
portion of the adapter top is pointing just to the
left of drum center.

Figure 2 Angled Adapter Just Left of Center

3.

Turn down the locking ring until it contacts the
drum. Use an appropriately sized pipe wrench or
adjustable wrench to tighten the adapter until the
widest portion of the adapter top is in line with the
drum center.

Back

Back

Back Geared

Geared

Geared Agitator

Agitator

Agitator Models

Models

Models 26B618,

26B618,

26B618,

26B619,

26B619,

26B619, 26B630,

26B630,

26B630, 26B631,

26B631,

26B631, 26B632,

26B632,

26B632, and

and

and

26B633

26B633

26B633

See the following sections for part information:

•

Models 26B618, 26B619, page 35

•

Models 26B630, 26B631, 238250, page 33

•

Models 26B632, 26B633, page 37

Assembling

Assembling

Assembling and

and

and Positioning

Positioning

Positioning the

the

the Agitator

Agitator

Agitator

With

With

With an

an

an Elevator

Elevator

Elevator

Mount the drum cover as described in manual
306287. The elevator must be in the down position
when you do any work on the elevator, agitator,
or drum cover assembly. Do not go under the
elevator when it is raised. Proceed to step 1 in

Installation With or Without an Elevator, page 11

Without

Without

Without an

an

an Elevator

Elevator

Elevator

If your system does not have an elevator, install the
Handles Kit 237524 to facilitate handling the drum
cover and agitator. Two people are needed to safely
lift and move the drum cover and agitator. Place two
standard 55 U.S. gallon (45 Imperial gallon) barrels
14 in. (36 cm) apart. Center the drum cover on the
barrels with the Graco logo centered and facing you,
as shown in the following figure. Proceed to step 1 in

Installation With or Without an Elevator, page 11

Figure 3 Assembling and Positioning Agitator
Without an Elevator

10

3A4792G

«
...
8
9
10
11
12
...
»

Содержание 25C528

















































Отзывы:

Нет отзывов

Похожие инструкции для 25C528

Бренд: Bahco Страницы: 9

Бренд: Federal Страницы: 43

Бренд: Nederman Страницы: 255

MiniLift160 Classic

Бренд: Handicare Страницы: 28

Бренд: Hands Free Farm Страницы: 24

Бренд: i-Optik Страницы: 75

Бренд: ubicquia Страницы: 36

Бренд: Daikin Страницы: 12

Бренд: Napoleon Страницы: 3

Бренд: Daikin Страницы: 52

i-Digits Access

Бренд: Össur Страницы: 231

Бренд: Xtricity Страницы: 4

Бренд: Warner Electric Страницы: 14

Бренд: Aspect Medical Systems Страницы: 104

Бренд: Hupfer Страницы: 153

Бренд: ATD Tools Страницы: 7

SPLICE-500 MKII

Бренд: Serpent Страницы: 8

Бренд: Wecan Technology and Lighting Co., Ltd Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды