background image

Installation 

6

3A3995L

System Monitoring

In a series progressive system, the primary and sec

-

ondary CSP valves can be connected with high pres

-

sure hoses so every outlet is linked together.

If one plunger in one of the CSP valves is not working, 

lubricant is no longer supplied to any of the outlets.

If one of the secondary CSP valves is blocked, then the 

primary CSP valve is blocked and the entire system 

installed downstream from the pump stops working.

A cycle indicator makes it possible to monitor the oper

-

ation of the entire system.

Cycle Indicator 

A CSP valve can be equipped with a cycle indicator pin. 

The cycle indicator is connected to the plunger and 

moves back and forth during plunger movement and as 

lubricant is distributed. 

NOTE

A micro limit switch/proximity switch/sensor can 

be installed to the cycle indicator to monitor the system 

electronically.

Electric System Monitoring

A system can be set up to use an electronic controller 

or to use a pump with a built in controller. A 

micro-limit/proximity switch/sensor can be installed to 

the cycle indicator on the CSP block and connected to 

the electronic controller. Together they control the 

pump operating time by counting cycles until the preset 

number of cycles has occurred.

The system can be set up to indicate a fault if the preset 

run time expires before the preset number of cycles are 

counted.

Proximity Switch Kits

NOTE: Available only for CSP valves with an indicator 

pin.

To install the proximity switch kit in the system, select 

the correct adapter from the package. Each package 

contains two types of adapters. The cylindrical adapter 

fits with the series A CSP valve (F

IG

. 2), and the rectan

-

gular adapter fits with the series B CSP valve (F

IG

. 3).

NOTE

Use of the wrong adapter will cause the system 

to fail.

26C822 Switch, PNP, 9.5 in. (24 cm) Cable with M12 

connector

26C823 Switch, PNP, 16.5 ft (5 m) Cable with flying 

leads

F

IG

. 2: Series A CSP Valve

F

IG

. 3: Series B CSP Valve

Cylindrical Adapter

Rectangular Adapter

Содержание 24Z477























Отзывы: