manualshive.com logo in svg

Graco 24F307, Операция

Поделиться
Скачать
Graco 24F307 Скачать руководство пользователя страница 25

Smart Control Operation

3A2090A Operation

25

Operation in Manual Mode

1.

Make sure engine is running and main power switch 
is on.

2.

Use Gun Selector Switches to select guns and line 
type. 

3.

Press and hold Gun Trigger Control button to spray 
a line. Release button to stop spraying. 

Operation in Automatic Mode

Preset Skip Patterns

1.

In the 

AUTOMATIC MODE

, the striper is equipped 

with Preset Skip Patterns. To select a preset skip 
pattern, press 

MODE

 button to move to 

AUTO-

MATIC MODE

.

2.

Press 

SETUP

 button to view preset skip patterns. 

3.

Use 

SELECT

 arrows to mark desired pattern. Press 

SETUP

 key to save and return to 

AUTOMATIC 

MODE

 display.

4.

Use Gun Selector Switches to select guns and line 
type. 

NOTE:

 Striper must be moving for guns to activate.

5.

With the striper moving faster than 0.3 mph (0.5 
kph) press Gun Trigger Control Button to stripe. 
Press button again to stop striping or reduce speed 
to below 0.3 mph (0.5 kph). 

ti9915b

 

,:B,DG"


!""#

$%&'()

ti18552a

ti18969a

ti18564a

 

,:B,DG"


!""#

$%&'()

ti9915b

 

@02





##,!#
8",B!:;

s

 

ti9942b

ti18969a

Programmed line pattern

OFF position disengages gun

Continuous line

ti18564a

Содержание 24F307





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды