manualshive.com logo in svg

Graco 24F307, Операция

Поделиться
Скачать
Graco 24F307 Скачать руководство пользователя страница 11

Setup/Startup

3A2090A Operation

11

14. Increase pressure control enough to start pump. 

Allow fluid to circulate for 15 seconds.

15. Turn pressure down, turn prime valve horizontal. 

Disengage gun trigger safety.

16. Hold gun against grounded metal flushing pail. Trig-

ger gun and increase fluid pressure slowly until 
pump runs smoothly.

17. Inspect fittings for leaks. If leaks occur, turn sprayer 

OFF immediately. Perform 

Pressure Relief Proce-

dure

. Tighten leaky fittings. Repeat 

Startup

, steps 1 

- 7. If no leaks, continue to trigger gun until system 
is thoroughly flushed. Proceed to step 9.

18. Place siphon tube in paint pail.

19. Trigger gun again into flushing fluid pail until paint 

appears. Assemble tip and guard.

20. Repeat steps 6 - 10 on second gun for 2-gun mod-

els. 

SwitchTip and Guard Assembly

1.

Engage trigger safety. Use end of SwitchTip (A) to 
press OneSeal (B) into tip guard (D), with curve 
matching tip bore (C).

2.

Insert SwitchTip in tip bore and firmly thread assem-
bly onto gun.

To avoid skin injection injury, do not stop leaks with 
your hand or a rag. 

15 SEC.

ti3442a

ti6472a

3304c

ti3441a

ti3442a

PAINT

ti3316a

ti3324a

ti6638a

A

B

C

D

ti3325a

ti3327a

Содержание 24F307





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды