background image

2

307363

Table of Contents

Warnings

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Installation

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Operation

8

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Pressure Relief Procedure

8

. . . . . . . . . . . . . . . . . . . . . . . 

Maintenance

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Troubleshooting

12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Service

14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Parts

18

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Technical Data

20

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Dimensions

22

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Mounting Hole Layout

22

. . . . . . . . . . . . . . . . . . . . . . . . . . 

Warranty

24

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Graco Information

24

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
corresponding instructions.

WARNING

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

D

This equipment is for professional use only.

D

Read all instruction manuals, tags, and labels before operating the equipment.

D

Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco
distributor.

D

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

D

Check equipment daily. Repair or replace worn or damaged parts immediately.

D

Do not exceed the maximum working pressure of the lowest rated system component. These
heaters have a 3000 psi (21 MPa, 210 bar) maximum working pressure.

D

Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Tech-
nical Data
 section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

D

Do not use hoses to pull equipment.

D

Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 82

_

C (180

_

F) or below –40

_

C (–40

_

F).

D

Do not touch the heater during operation; it is very hot.

D

Comply with all applicable local, state, and national fire, electrical, and safety regulations.

Содержание 226816

























Отзывы: