background image

3

308118

WARNING

SKIN INJECTION HAZARD

Spray from the gun/valve, hose leaks, or ruptured components can inject fluid into your body and

cause extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the

skin can also cause serious injury.

D

Fluid injected into the skin might look like just a cut, but it is a serious injury.

Get immediate surgi-

cal treatment.

D

Do not point the gun/valve at anyone or at any part of the body.

D

Do not put your hand or fingers over the spray tip/nozzle.

D

Do not stop or deflect leaks with your hand, body, glove or rag.

D

Do not “blow back” fluid; this is not an air spray system.

D

Always have the tip guard and the trigger guard on the gun when spraying.

D

Check the gun diffuser operation weekly. Refer to the gun manual.

D

Be sure the gun/valve trigger safety operates before spraying/dispensing.

D

Lock the gun/valve trigger safety when you stop spraying/dispensing.

D

Follow the

Pressure Relief Procedure

on page 9 whenever you: are instructed to relieve pres-

sure; stop spraying/dispensing; clean, check, or service the equipment; and install or clean the

spray tip/nozzle.

D

Tighten all fluid connections before operating the equipment.

D

Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.

Permanently coupled hoses cannot be repaired; replace the entire hose.

D

Use only Graco approved hoses. Do not remove any spring guard that is used to help protect the

hose from rupture caused by kinks or bends near the couplings.

MOVING PARTS HAZARD

Moving parts, such as the air motor piston, can pinch or amputate your fingers.

D

Keep clear of all moving parts when starting or operating the pump.

D

Before servicing the equipment, follow the

Pressure Relief Procedure

on page 9 to prevent the

equipment from starting unexpectedly.

Содержание 224348





























Отзывы: