background image

INSTRUCTIONS–PARTS LIST

307–944

Rev.  G

Supersedes F

and PCN G

SEVERE-DUTY

Displacement Pumps

3000 psi (210 bar) Maximum Working Pressure

Part No. 222–012, Series B

0.554 in.

 (357.4 mm

) Effective Displacement Area

Part No. 222–015, Series A

0.443 in.

 (285.8 mm

) Effective Displacement Area

Part No. 222–017, Series B

0.370 in.

 (238.7 mm

) Effective Displacement Area

Part No. 222–019, Series A

0.277 in.

 (178.7 mm

) Effective Displacement Area

Severe-Duty Displacement Pumps have an abrasion
and corrosion-resistant displacement rod and cylinder.
Refer to 

Technical Data on the back cover for Wetted

Parts information.

Table of Contents

Warnings

2, 3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Service

4, 5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Accessories

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Dimensions

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Parts

6, 7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Repair Kits

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Technical Data

8

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Warranty

8

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Graco Phone Numbers

8

. . . . . . . . . . . . . . . . . . . . . . . . . . 

WARNING

Plural Component Materials Hazard
Graco Inc. does not manufacture or supply any of the reactive chemical materials that may be used in this
equipment and is not responsible for their effects. Because of the vast number of chemicals that could be
used and their varying chemical reaction, before using this equipment the buyer and the user should deter-
mine all facts relating to the materials used, including any of the potential hazards involved. Particular inquiry
and investigation should be made into the potential dangers relating to toxic fumes, fires, explosions, reaction
times, and exposure of human beings to the individual components or their resultant mixtures. Graco as-
sumes no responsibility for loss, damage, expense or claims for bodily injury or property damage, direct or
consequential, arising from the use of such chemical components.

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

COPYRIGHT 1988, GRACO INC.

This manual contains important 
warnings and information. 
READ AND RETAIN FOR REFERENCE

Содержание 222012









Отзывы: