13
12
See images -
13
Button Functions
SPEED – Press On /Off button or press any speed
from 1 to 6. When pressing On/Off button, it
automatically starts with the last speed setting that
was selected before the swing was turned off.
ON/OFF POWER - Press to turn ON and turn
OFF. Press button to stop swing motion.
MUSIC - Push “Music” button to turn on music.
Push button again to advance to next track. There
are 10 songs.
MUSIC/NATURE OFF - Press button to turn OFF.
VOLUME— Press the plus (+) to raise the volume
and the minus (-) to lower the volume. There are
5 volume settings.
NATURE SOUNDS— Push “Nature” button to
turn on nature sound selection. Each press will
change to the next nature sound. After the 5th
sound is selected, it will return to the first track.
TIMER— Push “Timer” button to set the timer for
the swing and/or Music/Nature sounds. If the timer
button is not pushed, the swing and/or music/
nature sound will continue to play until the power
on/off button is pushed or the music/nature off
button is pushed.
When using the timer with the product on, if the
button is pushed once, the red speed light will
flash once and timer is set for 10 minutes. Pushing
the timer button a second time will increase the
run time to 20 minutes and the red speed light
will flash twice.
Pushing a third time will increase the time to 30
minutes and the red speed light will flash three
times.
When using the timer with the Music/Nature
sounds on, the timer will set to 10, 20 or 30
minutes as described for the swing, but there
will be no flashing light.
37
38
39
43
Storage
Push buttons to fold.
44
Assembling Mobile
See images -
See images -
46
53
Mix N’ Move Toys
52
56
See images -
44
45
Front Tube
Rear Tube
See images -
See images -
12
Use slide adjuster at shoulder and waist for
further adjustment. Repeat on other side.
When changing harness strap slots,
MAKE SURE harness straps are going through
same slots in seat pad.
The harness straps must go into the slot that
is even with or slightly above the shoulders.
Avoid twisting straps.
27
28
29
6
1
Instructions
Assembling Product
Attaching Tray
Squeeze recline handle on seat and lower
seat before attaching tray.
Line up tray on edge of seat and insert peg
into hole and close tray.
See image
7
9
To Secure Child
22
30
Installing Batteries
27
31
To Adjust Recline
With baby out of swing, open the battery
compartment lid by inserting a screwdriver into
the coin slot. Insert three D(LR20-1.5V) cell
batteries.
CHECK that the batteries are put in correctly.
Your swing will not run if the batteries are put
in backwards.
35
36
Place feet with the text “FRONT” onto the front
tube as shown. The text “FRONT” should face
floor.
Secure front foot with screw. Repeat on other side.
Snap front tube onto swing legs. CHECK that all
tubes are securely attached.
16
17
18
See image
See image
CHECK that hangar tubes are secure in brackets by
pulling firmly on them.
19
20
21
Head Support
Only use this head support on this swing. Never
use this head support on any other product.
32
Starting Product
WARNING: avoid serious injury from falling or sliding
out. Always use harness. After fastening buckles, adjust
belts to get a snug fit around your child.
TO TURN PRODUCT ON:Press On /Off button or
press any speed from 1 to 6. When pressing On/Off
button, it automatically starts with the last speed setting
that was selected before the product was turned off.
Observe the swinging motion for a minute. It takes
time for the product to adjust to a setting. Change
setting if needed.
A small, quiet baby will swing higher on each setting
than a larger, more active baby.
Your seat may be stopped at any time the motor is
running without damaging the motor. Push product to
restart.
If your product motor stops operating by itself, a
protective device may have been activated. Turn off
motor, wait three minutes, then restart swing.
TO TURN PRODUCT OFF: Press On /Off button.
EN
Attaching Legs
14
15
The double buttons must fit into the channels
inside the housings. Button MUST snap through
hole.
Insert rear legs into holes in housing as shown.
Button MUST snap through hole.
REPEAT steps 10 through 11 with other housing
and legs.
See image
Swing the legs outward until the single button snaps
into its notch. CHECK that the legs are properly
attached by twisting them in the housings.
10
11
11
12
13
See images
-
See images -
33
34
AC Adapter
40
41
42
8C
8
Содержание 1L998PTWEU
Страница 1: ...LOVIN HUG Instructions IMPORTANT READ CAREFULLY AND KEEP FOR FUTURE REFERENCE GIM 0032G...
Страница 32: ...63 62 9 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 3 RU 9 Graco...
Страница 38: ...75 74 9kg 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 3 EL 9kg Graco To...
Страница 40: ...79 78 AR 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 9 Graco...
