manualshive.com logo in svg

GPI M-1115S-AU, Руководство пользователя для продукта

Поделиться
Скачать
GPI M-1115S-AU Скачать руководство пользователя страница 11

GETTING ST

ARTED

SAFETY

 / 

SPECIFICA

TIONS

ASSEMBL

Y /

 

INST

ALLA

TION

OPERA

TION

TROUBLESHOOTING

MAINTENANCE /

 

REP
AIR

9-EN

GETTING ST

ARTED

SAFETY

 / 

SPECIFICA

TIONS

ASSEMBL

Y /

 

INST

ALLA

TION

OPERA

TION

TROUBLESHOOTING

MAINTENANCE /

 

REP
AIR

OPERATION

IMPORTANT:

 Always follow safety precautions when operating this 

equipment. Review the Safety Instructions.

To prevent physical injury or property damage, 
observe precautions against fire or explosion 

when dispensing fuel. Do not operate the system in the presence  
of  any source of  ignition including running or hot engines, lighted 
tobacco products, gas or electric heaters, or any type of  electronic 
device. A spark can ignite fuel vapors.

Before each use, repair leaks around seals or 
connections. Make sure hoses are in good 

condition and connections are tight.

NOTE: Make sure the work area is dry.

Make sure the pump is properly grounded. Repair 
any corroded or damaged wiring before use.

NOTE: Ensure the tank contains enough fuel.

IMPORTANT:

 Make sure the fuel is not contaminated with debris. 

Tighten loose tank lids regularly.

Dispensing Fuel

1. Turn on the pump by removing the nozzle from the holder and pushing

up the switch lever. Insert the nozzle into the receiving tank and

squeeze the handle to start fuel flow. When done, release the nozzle

handle, turn the pump off and return the nozzle to its holder.

IMPORTANT:

 

This pump is designed to be self-priming. If fuel is not 

delivered within 15 to 20 seconds, turn the pump off and refer to priming 

information in the Troubleshooting Section.

An automatic bypass valve prevents pressure build 
up when the pump is on with the nozzle closed. To 

avoid pump damage, do not run the pump more than 10 minutes with 
the nozzle closed.

Never leave the pump running without fluid. Dry 
running can damage the pump components, and 

will void the warranty.

IMPORTANT:

 

This is an intermittent duty pump, after running the pump 

for a maximum of 30 minutes, allow it to cool for 30 minutes.

Thermal Motor Protector
IMPORTANT:

 The motor is provided with an internal auxiliary 

temperature-limiting device. Excessive motor heat can trip the device. 

It resets automatically after the motor has cooled.
1. If the auxiliary temperature limiting device trips, reset by turning the

switch OFF. Let the pump cool then turn ON again. If the device

trips again, see the Troubleshooting Section of this manual.

Always turn the pump off  if  the temperature-
limiting device trips. If  left on, the pump will 

automatically reset when cool and start pumping.

Never leave pump running unattended.

Содержание M-1115S-AU

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды