background image

Global Parts Enterprise LLC. Limited Warranty

Global Parts Enterprise LLC. (“GPE LLC.”) warrants that the retail hardware product herein (“Product”) is free of material defects in materials 

and workmanship that result in Product failure during normal usage, according to the following terms and conditions:

1.

The limited warranty extends only to the original end-user purchaser and holder of this warranty. The warranty is not transferable or assignable 
to any subsequent purchaser.

2.

Proof of purchase of the Product in the form of a dated itemized receipt or invoice is required to be eligible for this limited warranty.

3.

The limited warranty is ONLY applicable in the country or territory where the product was purchased from an authorized GPE LLC. retailer and 
excludes any product that has not been purchased as new or is obtained as a result of the purchase of a non-GPE LLC. product.

4.

During the Warranty Period (as provided below), GPE LLC. will repair, or replace, at GPE LLC. sole option, any defective parts or any parts that 
will not properly operate for their intended purpose with new or refurbished parts if such repair or replacement is needed.

a.

The limited warranty for the Product extends for Ninety (90) days from the date of the purchase (“Warranty Period”). The warranty 
period will be extended by each whole day that the Product is out of the possession for repair under this warranty.

b.

GPE LLC. will pay for the labor charges incurred by GPE LLC. in repairing or replacing the defective parts during the Warranty Period from 
the date of your purchase.

c.

GPE LLC. also warrants that the repaired or replaced parts will be free from defects in material and workmanship for a period of FIFTEEN 
(15) days from the date of repair or replacement, or for the remainder of the Warranty Period, whichever is greater.

5.

GPE LLC. does not warrant uninterrupted or error-free operation of the Product. GPE LLC. is not under any obligation to support the Product for 
all operating environments, including but not limited to.

6.

For repairs during warranty period, please refer to the Product Returns section of the GPE LLC. Customer Support Services documentation 
accompanying the Product for repair information. This document will provide you with contact information for a GPE LLC. office and step-by-
step procedures for returning the Product for warranty service.

a.

You must provide proof of purchase of the Product by a dated itemized receipt or invoice.

b.

You will bear the cost of shipping the Product to GPE LLC.. GPE LLC. will bear the cost of shipping the Product back to You after 
completing the warranty service.

c.

You will be issued a Return Authorization Number. Please write the RA number on the outside of the package. GPE LLC. will not accept a 
return that does not have a return authorization or the RA number on the outer packaging.

Only return the defective item(s). GPE LLC. is not responsible for other products or accessories returned with the defective item.

11. Warranty Information

Page 12

Содержание ProMax-900






















Отзывы: