manualshive.com logo in svg

Gotting HG G-193 0-B Series, Руководство пользователя

Поделиться
Скачать
Gotting HG G-193 0-B Series Скачать руководство пользователя страница 24

Device Description HG G-193x0-B | English, Revision 02 | Date: 07.05.2018

24

Chapter 6 – Configuration

6.4.6 HG G-193x0ZB: (5) CAN Config

Configuration of NodeID and Baudrate. The sub menu CAN-Status lists the reception and

 

transmission counters as well as possible errors. Additionally CAN statistics are shown (RX

 

packet counter, TX packet counter, error counter).

Figure 16

Menu CAN config

6.4.7 Firmware Update

If necessary this menu can be used to update the firmware of the inductive guidance sensor 
to a new version. In order to update the firmware the device has to be put into DFU (Device

 

Firmware Upgrade) mode.

Figure 17

Firmware Update Menu

After pressing 

 the connection in the terminal program should be closed until the update 

in DFU mode is finished.

You need the 

.dfu

 firmware file and the software 

DfuSe

 by ST Microelectronics®. You can

 

request 

.dfu

 firmware files from Götting and they will be sent to you via e-mail. You can

 

download the DfuSe software from the following address:

Link

http://www.st.com/en/development-tools/stsw-stm32080.html

 HG 193x0 ZB V1.01               CAN config                          Goetting KG

 NodeID:   1
 Baudrate: 250 kBit/s

 1:  Edit Node ID
 2:  Edit Baudrate
 3:  CAN Status

 Press any other key to quit

Press y to reboot the device in DFU mode
Press any other key to quit

Содержание HG G-193 0-B Series







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды