Gorilla Playsets Rambler 1400 Скачать руководство пользователя страница 10

Страница: 10 / 94

Safety and Maintenance Tips for Your New Play Set:

(continued)

Playgrounds should be inspected on a regular basis. If any of the following conditions are noted,

they should be removed, corrected, or repaired immediately to prevent injuries.

• Hardware that is loose, worn or that has protrusions or projections.

• Exposed equipment footings.

• Scattered debris, litter, rocks, or tree roots.

• Splinters, large cracks, and decayed wood components.

• Deterioration and corrosion on structural components, which connect to the ground

• Missing or damaged equipment components, such as handholds, guardrails, swing seats.

• Check all nuts and bolts frequently during the usage season and tighten as required.

(But not so tight that you crack the wood) We recommend you check the swing beam and

hardware often due to wood expansion and contraction. It is particularly important that this

procedure be followed at the beginning of each season.

• Remove plastic swing seats and take indoors or do not use when the temperature drops below

32°F.

• Oil all metallic moving parts monthly during the usage period.

• Check all coverings for bolts and sharp edges twice monthly during usage season to be certain

they are in place. Replace when necessary. It is especially important to do this at the beginning

of each new season.

• Check swing seats, ropes, cables and chains monthly during usage season for evidence of

deterioration. Replacement should be made of any swing seat that has developed cracks in the

plastic seats. Ropes, cables and chains should be removed and replaced if excessive wear is

found. Contact us for warranted replacement parts.

• For rusted areas on metallic members such as monkey bars, hand supports brackets, etc.;

sand and repaint, using a non lead-based paint meeting the requirements of Title 16 CRF Part

1303.

• Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season

causing splinters to appear. Light sanding may be necessary to maintain a safe playing

environment. If you are treating your play set with stain regularly, it will help prevent severe

checking/splitting and other weather damage.

• Once or twice a year, depending on your climate conditions, you must apply some type of

protection (sealant) to the wood of your unit. Prior to the application of sealant, lightly sand any

“rough” spots on your set. Please note this is a requirement of your warranty.

• Creating and maintaining the play set on a level location is very important. As your children

play, your play set will slowly dig its way into the soil, and it is very important that it settles

evenly. Make sure the play set is level and true once each year or at the beginning of each play

season.

• Rake the playground surface periodically to prevent compaction and maintain appropriate

depths.

• Disposal Instructions: When the play set is no longer desired, it should be disassembled

and disposed of in such away that no unreasonable hazards will exist at the time the unit is

discarded.

Содержание Rambler 1400































































































Результаты поиска

Содержание Rambler 1400

Отзывы:

Похожие инструкции для Rambler 1400

Бренды по названию

Популярные бренды

Gorilla Playsets Rambler 1400, Руководство пользователя

Результаты поиска

Содержание Rambler 1400

Отзывы:

Похожие инструкции для Rambler 1400

Бренды по названию

Популярные бренды