Gorilla Playsets 1500HWF Скачать руководство пользователя страница 21

Страница: 21 / 177

T-NUT

CORNER POST

BOARD YOU ARE

ATTACHING TO

CORNER POST.

WASHER

HEX HEAD BOLT

FRONT SIDE OF

CORNER POST

BACK SIDE OF

CORNER POST

T-NUT

FLANGE

IS HERE.

BOARD YOU

ARE ATTACHING

TO CORNER POST.

WASHER

HEX HEAD BOLT

CROSS SECTION VIEW

OF BOARD, CORNER

POST AND FASTENERS.

CORNER POST

DETAIL A

SCALE 2 : 1

FLANGE

SHAPED END

WITH TEETH

TEETH

BARREL

SHAPED

END GOES

INTO HOLE IN

CORNER POST.

T-NUT DETAILS

THREADS ON

INSIDE OF

BARREL .

HOW A T-NUT WORKS

THE FIRST STEP IN OUR ASSEMBLY INSTRUCTIONS IS TO INSERT T-NUTS INTO THE CORNER

POSTS. A T-NUT IS A FASTENER WHICH IS THREADED ON THE INSIDE AND IT FUNCTIONS

JUST LIKE A STANDARD HEX NUT. YOU INSERT THE T-NUTS INTO THE PREDRILLED HOLES IN

THE CORNER POSTS.
THE T-NUT HAS A BARREL SHAPED END WHICH GOES INTO THE HOLE IN THE CORNER POST.

THE T-NUT ALSO HAS AN FLANGE SHAPED END WITH TEETH. THE TEETH PENETRATE INTO THE

CORNER POST WOOD TO PREVENT THE T-NUT FROM SPINNING WHEN YOU TIGHTEN THE

HEX HEAD BOLT.
SHOWN BELOW YOU WILL SEE THE T-NUT IS HAMMERED INTO THE CORNER POST ON THE

BACK SIDE. THE BOARD IS BEING ATTACHED ON THE FRONT SIDE OF THE CORNER POST.

Содержание 1500HWF


















































































































































































Результаты поиска

Содержание 1500HWF

Отзывы:

Похожие инструкции для 1500HWF

Бренды по названию

Популярные бренды

Gorilla Playsets 1500HWF, Руководство пользователя

Результаты поиска

Содержание 1500HWF

Отзывы:

Похожие инструкции для 1500HWF

Бренды по названию

Популярные бренды