Gorilla Playsets 1500CWR Скачать руководство пользователя страница 57

Страница: 57 / 119

4 "

USE 2-1/2" WOOD SCREWS

IN THESE LOCATIONS

CENTER DECK

SUPPORTS

2 X 6 BOTTOM

PANEL BOARD

HEAD SHOULD BE FLUSH TO THE

DECK SPACER

BOTTOM PANEL BOARD.

DECK SPACER

NOTE: THE TOP OF THE SCREW

DECK BOARD

2" WOOD SCREW

UNIFORM (APPROX. 1/4") SPACE

5/4 X 3-3/8 X 14-1/2"

BETWEEN THE DECK BOARDS.

TOP OF THE DECK BOARDS.

4: FASTEN DECK SPACERS AND DECK BOARDS TO THE

CENTER DECK SUPPORTS WITH 2" WOOD SCREWS.

2 X 4 X 70" CENTER DECK SUPPORTS TO THE 2 X 6

5/4 X 3-3/8 X 22-1/2"

5/4 X 6 X 47-1/2"

2: START WITH A 5/4 X 6 X 47-3/8"

DECK BOARD AT ONE END OF THE

FORT. CENTER THE BOARD

BETWEEN THE FRONT FACE BOARD

AND THE REAR BOTTOM PANEL

BOARD AND ATTACH IT WITH 2"

WOOD SCREWS THROUGH THE

PREDRILED HOLES AND INTO THE

DECK SUPPORT BELOW. LEAVE A

3: USING TWO 2-1/2" WOOD SCREWS, ATTACH THE

5/4 X 3-3/8 X 22-1/2"

DECK SPACER

5/4 X 3-3/8 X 14-1/2"

STEP 10A: DECK BOARDS

THE FOLLOWING STEP IS RECOMMENDED TO PREVENT POSSIBLE SPLITS IN THE WOOD

1: PRE-DRILL THE ENDS OF THE DECK BOARDS TO PREVENT INSTALLATION DAMAGE. PRE-DRILL BOTH ENDS WITH A

1/8" DRILL BIT AT THE DIMENSIONS SHOWN BELOW. THE HOLES AT 22-1/8" & 17-3/8" ONLY NEED TO BE DRILLED

ONCE.

8 "

4 "

17 38 "

Содержание 1500CWR
























































































































Результаты поиска

Содержание 1500CWR

Отзывы:

Gorilla Playsets 1500CWR, Руководство пользователя, Страница: 57 / 119

Результаты поиска

Содержание 1500CWR

Отзывы: