manualshive.com logo in svg

Gorilla Playsets 1500CWR, Руководство пользователя, Страница: 20 / 119

Поделиться
Скачать
Gorilla Playsets 1500CWR Скачать руководство пользователя страница 20

2 x 4 board

Corner post

Corner Post

4 x 4 board

PRE-DRILL LAG SCREW DIRECTIONS

posts with an 11/64" drill bit.  Remove the 

holes in the 4 x 4 board into the corner 

right.  Install the 4 x 4 board.

to drill the holes to a total depth of 2-5/16" as shown at 

4 x 4 board.  Continue to drill the holes to 

a total depth of 2-13/16" as shown at the 

the right.  Install the 2 x 4 board.

board into position.  Spot drill through the 

below.  Place the board into position.  Spot Drill through 

the holes in the 2 x 4 board into the corner posts with 

Example 5/16" diameter x 3-1/2" lag screw

the right.  Install the 2 x 4 board.

This would be like the 2 x 4 board installation shown 

drill the holes to a total depth of 2-5/16" as shown at 

an 9/64" drill bit.  Remove the 2 x 4 board.  Continue to 

Example: 3/8" diameter x 3-1/2" lag screw

This would be like the 2 x 4 board installation shown 

below.  Place the board into position.  Spot Drill through 

the holes in the 2 x 4 board into the corner posts with 

an 11/64" drill bit.  Remove the 2 x 4 board.  Continue 

Example 3/8" diameter x 5" lag screw

This would be like the 4 x 4 board 

installation shown below.  Place the 

LAG SCREW DIAMETER

DRILL BIT SIZE

5/16" DIAMETER

9/64"

3/8" DIAMETER

11/64"

Pre-drilling holes for lag screws will make it easier to drive the screws in by hand.

"Jobber" length drill bits are available in sizes that are longer than standard drill bits and 

those are ideal for the job.  When using the drill bit you will have to "spot" drill the post 

and then remove the board you are attaching to finish drilling the hole.

Pay attention to the DIAMETER of the lag screw you are installing

.  Your playset may 

come with two different diameter lag screws.  Each diameter will require a different size 

drill bit.  When installing lag screws 

DO NOT OVERTIGHTEN.

Corner Post

2 x 4 board

4 x 4 board

Corner Post

7 "

 3 16

"

16

 2 5

16

15

 4

" 

 2 13

16 "

Содержание 1500CWR
























































































































Отзывы:

Нет отзывов