Gorenje K15RLBK, Инструкция по эксплуатации

Страница: 14 / 50

14
normal and does not mean that the kettle
has any defects.
Depending on the hardness of the water
in your area, small spots may appear on
the heating element of your kettle when
you use it. This phenomenon is the result
of scale build-up on the heating element
and on the inside of the kettle over time.
The harder the water, the faster scale
will build up. Scale can occur in different
colours. Although scale is harmless, too
much scale can influence the
performance of your kettle. Descale your
kettle regularly by following the
instructions given in the chapter
‘Descaling’.
Electromagnetic fields (EMF)
This Gorenje appliance complies with all
standards regarding electromagnetic
fields (EMF). If handled properly and
according to the instructions in this user
manual, the appliance is safe to use
based on scientific evidence available
today.
This appliance is marked according to the
European directive 2012/19/EU on Waste
Electrical and Electronic Equipment
(WEEE).
This guideline is the frame of a European-
wide validity of return and recycling on
Waste Electrical and Electronic Equipment.
Boil-dry protection
This kettle is equipped with boil-dry protection.
This device will automatically switch the kettle off if
it is accidentally switched on when there is no
water or not enough water in it. The on/off switch
will stay in ‘on’ position, but the power-on light ring
will go out. Set the on/off switch to ‘off ’ and let the
kettle cool down for 10 minutes. Then lift the kettle
from its base to reset the boil-dry protection. The
kettle is now ready for use again.
Before first use
1. Remove stickers, if any, from the base or kettle.
2. Place the base on a dry, stable and flat surface.
3. Rinse the kettle with water.
4. Fill the kettle with water up to the maximum level
and let it boil once
(see ‘Using theappliance’).
5. Pour out the hot water and rinse the kettle once
more.
Using the appliance
1. Open the lid.
2. Fill the kettle with water.
You can fill the kettle either through the spout or
through the open lid.
3. Close the lid.
Make sure that the lid is properly closed to prevent
the kettle from boiling dry.
4. Place the kettle on its base.
5. Put the plug in the wall socket.
6. Set th
e on/off switch to ‘I’.
The power-on light ring goes on and the kettle
starts heating up.
The kettle switches off automatically when the
water has reached boiling point.
Cleaning and descaling
Always unplug the appliance before cleaning it.
Do not use any abrasive cleaning agents, scourers
etc. to clean the kettle.
Never immerse the kettle or its base in water.
Descaling the kettle
Regular descaling will prolong the life of the kettle.
In case of normal use (up to 5 times a day), the
following descaling frequency is recommended:
−
Once every 3 months for soft water areas (up to
18 dH).
−
Once every month for hard water areas (more
than 18 dH).
1. Fill the kettle with water up to three-quarters of the
maximum level and bring the water to the boil.
2. After the kettle has switched off, add white vinegar
(8% acetic acid) to the maximum level.
3. Leave the solution in the kettle overnight.
4. Empty the kettle and rinse the inside thoroughly.
5. Fill the kettle with clean water and boil the water.
6. Empty the kettle and rinse it with clean water
again.
Repeat the procedure if there is still some scale in
the kettle.
You can also use an appropriate descaler. In that
case, follow the instructions on the package of the
descaler.
Environment
Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in
at an official collection point for recycling. By doing
this, you help to preserve the environment.