background image

50
3909

During the warranty period, only a service center authorized by the manufacturer may 

carry out any repairs.

Before making any repairs, make sure the appliance is disconnected from the power mains 
either by removing the fuse or by disconnecting the power plug from the wall outlet.

Unauthorized tampering with and repairs of the kitchen range (cooking hob) can result in 
electric shock or short circuit; hence, do not attempt to perform any repairs by yourselves. 
Leave such tasks to an expert or an authorized service unit. 

In case of minor faults or problems with the appliance operation, check the following 
instructions to see whether you can eliminate the causes by yourselves.  

A visit by a service technician during the warranty period 
will be charged if the appliance is not functioning because 
of improper use. Store these instructions in a place where 
they are always readily accessible; if pas the appliance 
on to another person, the instructions should also be 
included.

Following is some advice on rectifying some common 
problems.

Important

What happened...?

Possible cause

What to do?

The burners will not burn
The fl ame is uneven / 
unstable

Flame is uneven due to a 
wrong gas power setting.

Have an expert check he gas 
pipeline!

The fl ame from the burners 
suddenly changes

Wrongly assembled parts of 
the kitchen hob

Assemble the burner 
correctly.  

Burner ignition takes more 
time

Wrongly assembled parts of 
the kitchen hob

Assemble the burner 
correctly. 

The fl ame is extinguished 
shortly after ignition

Knob pressed too short or 
to weakly. 

Keep the knob depressed 
for a longer period of time. 
Before releasing it, pres it 
harder.

The grid has discolored in 
the burner area?

This is a commonplace 
phenomenon resulting from 
high temperature

Clean the grid with a metal 
care detergent. 

Electric power supply in 
general is interrupted?

The fuse may be blown.

Check the fuse in the fuse 
box and replace it if it is 
blown.

Electric ignition of the 
burners no longer works?

There are food or detergent 
residues between the spark 
plug and the burner.

Open and carefully clean the 
opening between the spark 
plug and the burner.

12

SPECIAL WARNINGS AND FAULT REPORTING

Содержание INFINITY GW6NINB

























Отзывы: