Instructions for use, installation and connection
53
•
did you set the oven to the conventional mode after using it
in the automatic mode (programmed)? Switch the mode
button to the position "Manual mode".
Baking results are disappointing...
•
did you remove the grease filter?
•
did you follow the instructions and warnings from the section
"Baking"?
•
did you strictly follow the information from the baking table?
Replacement of parts
The oven light bulb casing is under tension. Danger of
electric shock!
Before replacing the oven bulb switch off the cooker and cut it
from mains by removing the mains power fuse or disconnect
the protective device. Remember that the bulb is regarded as
consumption material and is not covered by the warranty.
Other accessories
Oven grid, biscuit tray, etc. may be ordered from the service
center. When ordering please quote the code and the type or
model of the appliance.
Hotplate control knobs are removed by pulling them outwards
and replaced by pushing the new ones back in place.
,
Oven light bulb
The bulb for replacement should meet the following
specifications: E 14, 230 V, 15 W, 300°C.
Unscrew the glass cover by turning it counter clockwise, and
replace the bulb. Screw the glass cover back in place.
Remember that the bulb is regarded as consumption
material and is not covered by the warranty.
Instructions for installation and connection
Safety precautions for the technician
•
Installation may be carried out only by qualified personnel.
•
The electric installation shall be equipped with a safety device, able
to disconnect the appliance from mains in all wires, with the
distance between contacts of not less than 3 mm in open position.
Good protection is provided by the LS-switches and/or fuses.
•
The connection may be carried out by rubber mains lead (type
HO5RR-F with green/yellow earth wire), PVC insulated mains lead
(type HO5VV-F with green/yellow earth wire) or other cables of
equal or better quality.
•
Distance between the cooktop and the kitchen hood must be at
least the distance, indicated in the instructions for use of the kitchen
extraction hood.
•
Panels, glue and furniture lining from artificial materials, adjacent to
the appliance must be temperature resistant (>75°C), otherwise
they might be deformed.
•
Mains lead behind the cooker must be placed in such manner to
avoid touching the back panel of the cooker because of the heat it
develops during operation.
•
Remove any packaging materials (foils, artificial foam, nails, etc.)
from the reach of children, because they represent potential
danger. Children may swallow small parts, or suffocate with foils.
Oven drawer
•
The oven drawer is protected from accidental opening.
•
It may be open by lifting upwards. To remove the drawer from
the cooker pull it out to the limit, then lift upwards and pull out
completely.
•
Never place any flammable or explosive substances in the
drawer.
•
The drawer is equipped with side slides on wheels. To insert it
back, slide the wheels into the slide guides and push inwards.
Leveling the appliance and extra support
(only with certain models)
The height of the cooker with the support is 90 cm, and without
support it is 85 cm. Left and right side of the support is equipped with
two wheels to facilitate relocation. In the front part, on both sides there
are two adjustable screws, used to level the cooker and adjust its
upper edge in line with the adjacent kitchen furniture. Adjustable legs
are accessible when the drawer is pulled out. Adjust the position of the
cooker by turning the legs in one direction or another. Adjustable legs
will be turned easier if the appliance is somewhat lifted up and tilted.
Additional support may be removed by unscrewing the four screws
holding it to the bottom of the cooker. In such case relocate the Some
cookers are equipped with four adjusting screws (two in front and two
at the back), used for leveling the appliance or adjusting its heights to
match the adjacent furniture.
Electrical connection
Open the connection box using the screwdriver, as
shown by the drawing on the cover.
Connection to the mains power can be done only by
the authorized service center or by qualified
personnel!
Wrong connection may damage the parts of appliance and
render your warranty viod!
Connecting voltage of the user’s installation (230 V against N)
must be verified by qualified electrician using the appropriate
tester.
Connector bridges must be positioned in accordance with
the installation connection!
