Gorenje DFGA9575BX, Инструкция по эксплуатации

Страница: 10 / 52

English
!
The appliance must be installed by a qualified
person in compliance with the instructions
provided.
!
Wear gloves when carrying out installation and
maintenance operations.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
Warning: Failure to install the screws or fixing device
in accordance with these instructions may result in
electrical hazards.
AIR VENT
(for ducting versions)
!
Prepare the hole and the air vent duct (150 mm
diameter).
!
Use a duct of the minimum indispensible length.
!
Use a duct with as few elbows as possible
(maximum elbow angle: 90°).
!
Avoid drastic changes in the duct cross-section.
!
Use a duct with an as smooth as possible inside.
!
The duct must be made of certified material.
!
Do not connect the hood to smoke exhaust ducts for
the products of combustion (boilers, fireplaces,
stoves, etc).
!
For the air vents comply with the provisions laid
down by the competent authorities.
In addition, the air must not be evacuated through a
hole in the wall unless specifically intended for this
purpose.
!
Fit air intakes in the room to prevent the hood from
creating a negative pressure in the room (which must
not exceed 0.04 mbar); if the hood is used at the
same time as non-electrical equipment (gas-, oil- and
charcoal-fired stoves, etc.) the exhaust gas may be
sucked in by the heat source.
FILTERING OR DUCTING VERSION ?
The hood may be in filtering or in ducting version.
Decide from the outset which type is to be installed.
For better efficiency, we recommend installing the
hood in the ducting version (if possible).
Ducting version
Version with external motor
The hood purifies the air and evacuates it to the
outside through an exhaust duct (diameter 150 mm).
Filtering version
The hood purifies the air and recycles the clean air
back into the room.
Only for hoods equipped with electronic control:
The 4th speed (intensive) is automatically lowered to
3rd speed after 5 minutes of operation to optimise
energy consumption.
- If the hood is left on (lights and/or motor), after 10
hours in the absence of commands from the user, it
will automatically switch to OFF condition with all
services switched off.
- The Buzzer emits a “beep” each time that a
command is set from the keyboard or remote control
(optional).
- In the event of interruption of power during the hood,
if you restore the hood in the OFF state, then the
engine must be reactivate manually.
CONTROLS
P1 P2 P3 P4 P5 P6 P7
P1: Filter alarm reset
P2: LED on/off - (only certain models: holding the
button down you can change the LED intensity
to High or Low).
Note: LED activation is displayed by P2 only when
the lift panel is completely open.
P3: Motor on/off - 1st speed
P4: 2nd speed
P5: 3rd speed
P6: 4th speed
P7: Lift panel up/down (during opening the panel can
be stopped at the desired height by pressing the
button a second time).
5' Timer function:
Holding the buttons P3, P4, P5 or P6 pressed down
(>2") the 5' Timer function is activated. When the time
has run out, the motor turns off and the lift closes. The
LEDs change from High to Low intensity. When the
function is active, the LED corresponding to the current
motor speed blinks.
Filter alarm display:
Grease filters: After 30h of motor operation, the LED of
the P1 button comes on for 30'' every time the motor
turns off.
Charcoal filter: After 120h of motor operation, the LED
of the P1 button blinks for 30'' every time the motor
turns off.