background image

Hardware 

 

 

USB 4112/ basicCON 4112 – User Manual 

2-5 

 

Addressing individual  

USB 4112

  boards in the  

GOEPEL electronics

  

USB 

Rack

  or  

basicCON 4112

  devices takes place exclusively according to 

the serial numbers: The device with the least serial number is always 

the device with the number  

1

 (but counting by considering all other  

GOEPEL electronics

  USB devices in the same system). 

 

 

To improve clarity, we recommend to arrange several  

USB 4112

  

boards (if applicable) in the order of ascending serial numbers  

in a  

GOEPEL electronics

 

USB Rack

 

 
 

 

The  

USB 4112

  board is supplied via the  

USB Rack

  in that it has been 

installed. 
 
Power supply for  

basicCON 4112

  can be effected via the USB interface 

(as far as it is configured for the required current of about 500 mA). 
For operating the  

basicCON 4112

  at passive USB hubs or laptops with 

lower power supply, use the two banana females for  

ext. Power Supply

 

(red = plus/ blue = minus)  

for supplying the device with a voltage of 7-25 VDC. 

Alternatively, you may use the female for the delivered AC adaptor 

plug with coaxial power plug (2.1 x 5.5mm/ plus polarity inside),  

see also  Figure 2-3. 
 
 

 

Used connector: 

Rosenberger D4S20A-40ML5-Z 
 
Connector for connecting cable (recommended): 

Rosenberger D4K10A-1D5A5-Z 

 

1

2

3

4

1

2

3

4

1

2

3

4

1

2

3

4

1

2

3

4

In1

In2

In3

In4

Out

 

Figure 2-5: Front panel USB 4112 

The following table shows the pinout of the LVDS females: 

 

Connection  Pin 

Signal 

Connection  Pin 

Signal 

In 1..4 

GND 

Out 

LVDS- 

LVDS+ 

Control 

Control 

LVDS+ 

LVDS- 

GND 

 
 

 

2.3.3

 

Addressing 

2.3.4

 

Power 

Supply 

2.3.5

 

Connector 

Pinout 

Содержание basicCON 4112
















Отзывы: