background image

 

 

15

ETC. AROUND THE BASE AS TO PROVIDE A SEAL BETWEEN THE SUPPORT AND THE 
BASE. THE BASE OR PLATFORM MUST BE SEALED AIRTIGHT TO THE FLOOR. 
 
 
Install the return air to terminate through the base under the heater. For installations where re-
turn air ducts cannot be run under the floor, the return air supply may be taken from the 
side(s). The solid bottom supplied must remain in place. 
When installed in the downflow position, on combustible material, a special sub-base must be 
installed.  

 

WHERE THE MAXIMUM REQUIRED AIR FLOW IS .8494 M3/S OR GREATER THE 
BOTTOM OR BOTH SIDES MUST BE UTILIZED FOR RETURN AIR SUPPLY. NEVER USE 
THE REAR OF THE HEATER FOR THE RETURN AIR CONNECTION. FULL SIZED 
RETURN AIR DUCT OPENINGS MUST BE UTILIZED. EMBOSSES ON THE SIDE OF THE 
HEATER ARE PROVIDED TO ACT AS A GUIDE. 

 

WARNING 

A SOLID METAL BASEPLATE IS INSTALLED ON THIS HEATER. THIS BASEPLATE MUST 
BE IN PLACE WHEN THE HEATER IS INSTALLED WITH SIDE(S) RETURN AIR DUCTS. 
FAILURE TO DO SO MAY PERMIT COMBUSTION PRODUCTS, INCLUDING 

CARBON 

MONOXIDE

, TO ENTER THE LIVING SPACE CREATING A POTENTIALLY HAZARDOUS 

CONDITION SUCH AS 

CARBON MONOXIDE

 POISONING OR DEATH. 

 

ELECTRICAL SUPPLY CONNECTIONS 

 
The electrical requirements are nominal 230v. 50Hz. A separate supply line with a current 
overload device and a manual switch, where required, must be installed. Wire with a minimum 
rating of 35

o

C temperature rise must be run directly from the main power supply to the heater. 

Copper conductors are preferred. 
 

WARNING 

NEVER RENDER THE DOOR SWITCH INOPERATIVE. DOING SO MAY ALLOW 

CARBON 

MONOXIDE

 TO ENTER THE DWELLING.  

 
 

WARNING 

THE GAS SUPPLY PIPE MUST NEVER USED FOR GROUNDING PURPOSES. 

 

CONTROL VOLTAGE CONNECTIONS 

 
THERMOSTAT INSTALLATION: 
Install the thermostat according to the instructions accompanying the thermostat. Run the 
thermostat wires into the control compartment. Connect the thermostat wiring as shown on the 
wiring diagram. The thermostat wiring should be adequately sized to eliminate voltage drop. 
Adhere to recommended color code to facilitate future troubleshooting. 
The thermostat should be located near the return air grille or opening. It should be approxi-
mately 1.27 m from the floor level. 

Содержание GMP Series



















Отзывы: