background image

12

13

V

in

V

out

Malla

Shield

Malla

Shield

A

HZ-

INT

SA

CTO

2C

A1

VP

MP

D

REF

RCPL-PLUS

LOTE

CODE

11758882

Colocar la parte superior de la regleta a 1,60m. del suelo.

Place the top part of the monitor connector at 1,60m. from the floor.

50mm.

50mm.

Presionar para abrir.

Press to open.

Ter, – and Malla (shield) are duplicated for easiest cascade installation of parallel
     monitors or telephones. If the first monitor is not placed on the connector, cascade units
     will not be powered.

escription of the RCPL-Plus 

D

monitor connector.

a

a

b

b

f

e

d

c

a. Wall attachment hole (x4).
b. Monitor attachment hook (x2).
c. Vertical wiring input.
d. Attachment clip.
e. Wiring input hole.
f.  Installation terminals:

positive, ground.
video signal coaxial input.
coaxial shield.
video signal coaxial output.
audio communication.
digital communication.
door bell push button input.
intercom.
auxiliary calling device output.
video distributor activation output.
2nd camera activation output.
optional device activation output.
twisted pair video signal.

+, –:
Vin :
Malla:
Vout :
A :
D :
HZ- :
INT :
SA : 
CTO :
2C :
A1 :
Vp, Mp :

L561 module for video installations 

E

with twisted pair cable.

andling the end of line jumper.

H

hanging the front film.

C

The end of line jumper is placed on the CN4 connector, that can be
     located on the monitor base.
     In case of twisted pair cable installations, the end of line jumper
     is placed in the EL561 module, also located in the CN4 connector
     of the monitor base.

Do not remove the jumper on monitors where the video cable finish.
     Remove the jumper on monitors where the video cable continue.

The monitor is supplied with a reversible front film, that allow the owner
     to choose between two colors.
To change the front film, remove the front plate by inserting a plain screwdriver
     in the triangle marks, as it is shown on the drawing.

MONITOR ADJUSTMENTS

MONITOR CONNECTOR DESCRIPTION

Locate the CN4 connector, that's placed in the monitor base.
     Remove the existing jumper and plug the EL561 module.

NOTE: on this type of installations the EL560 module must be
     plugged in the CN4 connector of the panel (page 7).
     Refer to the specific installation diagram.

Содержание 295 Series


















Отзывы: