background image

the base.

The 12 Volt DC power wire should be joined to the leads under the 
lamp with appropriate automotive wire attachments.  It is critical that 
polarity be observed.  The (+) lead of the RadioRay® is marked with a 
red tag.  The power should be fused at 10 Amps and be on an ignition 
switched circuit if possible.
 
PROGRAMMABLE REMOTE INSTRUCTIONS
The Golight® RadioRay® is controlled with a programmable remote 
with 6561 different channels.  This feature allows you the freedom to 
change the channel selection, and the receiver relearns the new 
selection.

PROGRAMMING THE TRANSMITTER.
This light has been pre-programmed at the factory, and it is not 
necessary to re-program the transmitter, unless you experience 
outside interference.

 1.  IMPORTANT:  Disconnect power by removing fuse or
    disconnecting vehicle battery.

 2.  Remove battery cover from remote control.

 3.  Set the 7 dip switches to a selection of your choice.  There are 3
    positions on each;  positive, negative and neutral.  Use a small
    screwdriver and select a position for each dip switch.  *Please note
    that the orientation of the +/– switch positions may vary among
    different models of wireless remote controls.

 4.  Insert both MN21 Duracell batteries with the +/– in the same
    direction.  Be sure batteries have adequate charge.

 5.  Replace battery cover.
    a. Depress the on/off button and hold it down.  Red LED will light.
    b. While holding the on/off button down, reinstall the power
        (replace fuse or connect vehicle battery).
    c.  Keep your finger on the on/off button for 5-6 seconds, and then
        release.  The light should now be programmed.

The Golight® RadioRay® Model 2000/2051 is designed to be 
permanently attached to a vehicle.  The 2-Speed Searchlight with 
Directional Flexibility is controlled by a wireless remote, which gives 
the operator a full 370

°

 horizontal rotation and a 135

°

 vertical tilt with 

fingertip control.  The RadioRay® provides superior light penetration 
with Cr5 PentaBeam™ technology.

The RadioRay® Includes:
 

  • RadioRay® Searchlight

 

  • Wireless Remote Control (must be kept clean and dry) 

 

  • 2 Duracell MN21 Batteries

 

  • Raincoat for Remote

 

  • Permanent Mounting Gasket

 

  • Mounting Screws and Caps

MOUNTING INSTRUCTIONS
Determine the location for the light on your vehicle or boat.  The small 
arrow on the base indicates the normal forward direction of the light.  
The light will rotate to the left of this arrow approximately 190

°

 and to 

the right approximately 190

°

.  The beam will angle down about 45

°

 

and angles up to 90

°

, a full vertical.  The location should take into 

consideration this beam movement to ensure optimum usability.

Once the position and orientation are decided upon—use the black 
rubber gasket as a footprint to mark the mounting of base to vehicle.  
Drill 1/4 inch hole though mounting surface in the middle of the 
footprint for passage of the power cord.  Use silicone sealant to fill 
opening around power cord.  IMPORTANT:  Allow 3" of cord to remain 
under the light to ensure full 370

°

 rotation.

You should choose screw or bolt fasteners appropriate to the surface 
to which you intend to attach the light.  If you intend to use the four 
small plastic caps provided to cover the screw heads once installed, a 
#8 round head is recommended.

The black gasket should be installed on the lamp base prior to 
attachment to the vehicle surface.  NOTE:  The small drain hole in the 
edge of the gasket should normally face opposite the forward 
direction of the vehicle—opposite the arrow molded in the front of

OPERATION OF GOLIGHT® RADIORAY®

 1.  Using the remote control, turn on the light by depressing the
  

on/off 

button. 

 2.  With the 4-way arrows on the remote control, rotate your light
    to the desired location.  Depending upon conditions, the
    wireless remote may be used up to 100 feet from the RadioRay®. 

 3.  The speed of the light rotation can be controlled by depressing
  

the 

+/– button one time and by depressing it again to

    restore the original speed. 

 4.  The spotlight should not be turned on when the snap on lens
    cover (rockguard) is attached.

BULB REPLACEMENT
The Golight® RadioRay® utilizes a Philips® H-9 bulb, which may be 
purchased through Golight, Inc.  — 308.278.3131 or 800.557.0098.

 ✱

 

This light is for off road and utility use only.  It is not designed for 

road use as a driving light.

 ✱

 

The RadioRay® complies with Part. 15 of the FCC Rules.  Operation 

is subject to the following two conditions:  (1) This light and remote 
may not cause harmful interference, and (2) this light and remote must 
accept any interference received, including interference that may 
cause undesired operation.

 ✱

 

FCC RULE Part. 15.21  -  Changes or modifications made by the 

user not expressly approved by Golight, Inc. for compliance could void 
the user’s authority to operate the equipment.

IMPORTANT SAFETY INFORMATION

 

This symbol is to alert you to important operating or servicing 

instructions that appear in your instructions.  Always follow basic 
safety precautions when using this product to reduce the risk of 
injury, fire or electric shock.

Отзывы: