A
LL
M
ODELS
#3005SS, #3008SS, 3015
Tornado
and
Whirlwind Floss Machine
10
OPERATING INSTRUCTIONS
TORNADO AND DELUXE WHIRLWIND
1. Plug in floss machine.
2. Before turning on the motor switch and with the spinner head stationary, fill floss head
about 90% full with sugar. Do NOT overfill! Whenever you add sugar to the floss head,
always fill it abour 90% full. This is necessary to obtain a balanced condition in the floss
head or excessive vibration will occur. Never add sugar when motor is running. After
adding Flossugar, manually rotate head to balance.
3. Flip Motor Switch to On position.
4. Flip the Heat Switch to Emergency position. This is for a fast warm up. Turn Heat Control
up until voltmeter indicator arrow moves into the red start area.
5. The machine should begin to make floss in a matter of a few seconds. After floss is being
produced, place Heat Switch in Normal position. Adjust the Heat Control until the voltmeter
indicator arrow moves into the green run area.
CAUTION
Never operate equipment for prolonged period of time with the
Heat Control in a position that causes the sugar to smoke. This
will result in excessive carbonization of the ribbon (heat element).
If you smell burning sugar or see smoke, reduce the heat.
6. Once you find the ideal setting for the Heat Control, you should be able to operate near this
position each time.
7. Read the section in this manual on Making Floss before going into full production
X-15R WHIRLWIND
1. Plug in floss machine.
2. Before turning on the main power and motor switch, and with the spinner head stationary, fill
the floss head about 90% full with sugar. Do Not Over Fill! Whenever you add sugar to the
floss head, always fill the head about 90% full. This is necessary to obtain a balanced condi
tion in the floss head and eliminate excessive vibration. Never Add Sugar When Motor Is
Running. After Adding flossugar manually rotate head to balance.
3. turn the Main Power and Motor Switch to the On position.
4. Turn Heat Range Switch to position "A". Rotate Heat Control Fine Tuning Knob to Maximum
position (No. 8). This setting will produce the fastest possible warm up.
5. You should start making floss in a few seconds. When the unit gets up to heat, it will probably
start to smoke. Reduce the Heat Control Fine Tuning setting to eliminate the smoke. If you
cannot eliminate the smoking in this manner, turn the Heat Range Switch to position "B" and
set the Heat Control Fine Tunning to postion No. 8 once more. If smoking continues reduce
the Heat Control Fine Tuning setting. If necessary, repeat once more with the Heat Range
Switch on "C".
NOTE:
You can fine tune in all three heat range positions.
6. Once you find the ideal Heat Range Switch and Heat Control Fine Tuning positions, you
should be able to operate near these positions each time you operate.
7. Read the section on Making Floss before going into full production.
Содержание Deluxe Whirlwind
