background image

Nacho Cheese  

 

Dispenser and Warmer

 

Model No. 5300, 5300EX 

 

Page 9 

 

 

gmpopcorn.com

6.

 

Set the desired time for any button following the chart below:  

 

 

 

 

 

 

 

Example - 

To set the dispense time of the Red Button to 9 seconds:  

On the middle bank of switches, turn “On” dip switch number 2 (1 Second) and 
number 5 (8 Seconds); turn “Off” the remaining dip switches in the middle bank. 

7.

 

For manual dispense, put all switches in the up (Off) position. 

8.

 

Replace the rear access panel before operation (Do NOT over tighten the screws). 

To Change Dispensing Temperature 

 

1.

 

With the Power Switch in the off position, unplug the warmer.  

2.

 

Remove the rear access panel and locate the Master Board pictured above. 

3.

 

Locate the Temperature Adjustment Potentiometer in the center of the Master Board.   

4.

 

Rotate the potentiometer clockwise to increase the temperature and counter-clockwise to 
decrease the temperature. 

5.

 

Replace the rear access panel before operation (Do NOT over tighten the screws). 

Switch Number

 

Dispense Time

 

½ Second 

1 Second 

2 Seconds 

4 Seconds 

8 Seconds 

16 Seconds 

7 (Yellow Only) 

32 Seconds 

8 (Yellow Only) 

64 Seconds 

 

Temperature Adjustment 
Potentiometer  
(140-155 Degree Control) 

WWW.CONCESSIONSTANDS.COM

 

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE 

concessionstands.com

Содержание 5300



















Отзывы: